L90-v8
-
Posts
74 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by L90-v8
-
-
the 3.9 14cux requires a speed sensor to adjust the fueling I got round this using the older inline type set up from a rrc efi the sensor is prc5956 I used rrc 3.5 speedo cables the short one is prc7949 long one prc8232 i modified one end to fit the defender dash you can fit a original defender speedo cable and not connect the speed sensor it will run fine but the difference it made really surprised me runs a lot better
-
in 2017 deutz engines still have the choice of 1-3 hole multi layer head gaskets its not just lr doing it
-
£70 a lamp that's expensive you can pick up land rover 7" for about £15 a side I brought a set of clear wipac ones for my escort for £35 for the pair I have a pair of those led ones on the defender paid £100 for the pair they work fine not as much depth as a good quality halogens or hids but still a good lamp better than the old sealed beam units
-
I'm also using that thermostat conversion kit also the stat housing I'm using is from 3.9 I suppose I could use the squirt to control the fan an pop my dash temp sensor in the stat housing but would it not give a duff reading tho in the stat housing when the stats shut would it read cooler than what it really was where as if it was in the manifold it would read a more true temp on the large diesels I work on the temp sensors are normally located in the head furthest away from the water pump like a tdi
-
I'm going to be putting a 4.6 thor into my 90 hopefully some time soon my current setup is a 3.9 serp 14cux system on a 3.5 efi lump I have one of niges coolant temp sensors for the megasquirt that parts sorted but I need to fit the temp sensor in the manifold for the dash gauge where has other people fitted this sensor my current setup has two ports for the heater I just removed the blanking plug an popped it in there but the thor only has one port and no blanked spare port the manifold is quite thin in places around the stat area so drilling and tapping could be tricky I think my best option would be tig a boss onto the manifold unless theres another option
-
I had modulars on before with the same tyres the challengers I got have more off set so I was able to get some decent steering lock back
-
not sure of the lift the springs are rrc red and whites but the rims are challenger and the tyres are 285/75 /16 km2
-
I agree 100% with the above the head is not great its knackered imo and if it was mine I would rectify the problem by sourcing another head or welding the crack but a friend of mine come over with a blown head gasket on 300tdi 4 months ago and wanted me to do the head gasket we pulled it apart it had 3 cylinders cracked between the valves and every cylinder was cracked around the glow plug it was warped to the point you could see clear daylight between number 2-3 using a straight edge he asked me what should he do with it I said the heads knackered find another head an fit a good one job done but he couldn't do that at the time as he needed to get to work the following day so we bolted it back together with a new gasket and its still going now 4 months later it don't over heat don't use a drop of oil or water runs perfect I cant believe it myself that it still runs with no issues I'm sure its ready to let go at any point he has now has sourced another good head for a sensible price so when we have a chance will get it sorted its not what I recommend and its not what I would personally do to my own vehicle but it shows you how forgiving a tdi is
-
I'm sure my old centre seat was fixed the frame was a one piece bottom and back that bolted directly to the seat box the threaded holes should already be there under the black round bungs at the front of the seat box cant remember how it bolted at the back I think it was nut and bolt not 100% sure the only other thing you need is the seat belt that's seperate an they bolt next to the driver an passenger seat belt buckles
-
forums facebook and e bay I find the mags to be on the pricey side theres a 2008 tdci for £9995 113,700 miles white 90 on e bay
-
1
-
-
11 hours ago, Mutley said:
On a more serious note, i thought i heard somewhere that the 1st. Lot of Td5's the engine was a bit laim power wise and the motor didn't improve till after 2007?
by 2003 they moved on from the 10-14p engines to the 15p its basically the same engine with the revised head without the extra fuel return drilling that commonly cracked also had different injectors and fuel regulator not sure about the bottom end the very early td5 were a bit unresponsive the power was there but they felt like they needed winding up to get going not sure when this got sorted by land rover having driven a standard 2004 15p its a totally different machine tune wise to the early one from the late 90's the later ones are a joy to drive
-
1
-
-
if your mainly using it on road I would go for a td5 with remap 15p lump the tdi is a great bit of kit but a remapped td5 imo is far better more power more torque an a lot smoother than a tdi an sound better than a 4 pot ive had na dervs tdi's td5 an v8's the td5 is the best derv out the bunch ive never had a tdci defender but had a couple of transits there also a grunty lump but don't seem to last
theres a lot of info on the net for the newer models and with code readers readily available don't be worried that there hard to work on
bodys rot everywhere where steel meets ali check the bottoms of the doors seat belt mounts footwells tub cappings seat boxes battery tray
chassis rot from front to back mainly outriggers and rear x member an behind where the front x member is an the rear chassis where the a frame bolts on
as above take someone with you who knows landrovers don't wear rose tinted glasses your budget will get you a good truck if you don't rush into it you will find exactly what you want
-
1
-
-
great pics they got some good looking motors over there
-
my defender manual says 135 psi min not sure if that's for a 8.13cr or 9.35cr
-
I have a 3.5 on 14cux with sd1 pistons an sd1 head gaskets its better than a low comp 3,5 on su's it still don't feel as good as the 3.9 efi I had in the d1 I agree with the above fit larger cc engine in the near future I'm hoping to fit my 4.6
-
16 minutes ago, RedLineMike said:
That's a 300tdi turbo & manifolds, give away is the turbo intake being rear facing & egr blanking plate
I noticed that too
-
11 hours ago, Maverik said:
Get a decent later model 300tdi D1, they're so underrated amazing vehicle and very cheap to boot, and they don't attract any attention what so ever.
2nd that i never was a fan of discoverys intill i had owned one ive owned a few tdi's v8's td5 loved them all as much as my 90 i cannot part her
-
it could be a different torque convertor a d1/rrc has a zf4hp22 and a d2/p38 has a zf4hp24 I think form memory the d1 v8 t/c is 4 bolt pattern an d2 is three bolt
-
On 18/09/2017 at 12:22 PM, Pawl12 said:
Have you driven any other td5 Disco 2s for comparison - eg before you bought this one?
1500rpm is about where the standard set up turbo begins to boost noticeably. Below this they don't pull well!
Could it be the behaviour is standard?
same as mine goes fine when its on boost
-
you will need to run it with both methods but it wouldn't hurt using a steam cleaner or a hose pipe to remove as much as possible before refitting the components you should be able to tell water ways from oil ways as the water ways should be tarnished a brown an full of that horrible grey sludge an oil more black in colour
-
sol x coolant flush or you can use dish washer tablets in the water system run an drain eventually it all comes out
-
green tune resistors are a job to find I popped to maplin an got a 470 ohm resistor for less than 50p I got the 2 watt one as there easier to handle i had a spare plug kicking around ard soldered it to the existing wires wrapped it in shrink wrap job done
-
mine don't rub with 285's with plus 5 pin on pin I cannot say if 37" will fit tho
-
its an easy conversion to do get some steel pipe of the correct diameter use the original filler neck hose on the tank just needs trimming to suit an get a filler neck hose that's fuel safe for the filler end an join the whole lot together just make sure the pipe is not level an has a slight fall towards the tank I have had no issues you can just make out the black pipe above the rear spring
Rear Corner Protection
in Defender Forum (1983 - 2016)
Posted
first four sell those type off the shelf without the needing any mods