Jump to content

RPiranha

Getting Comfortable
  • Posts

    12
  • Joined

  • Last visited

Everything posted by RPiranha

  1. Has anyone had this issue before? Brand new Britpart seal has split along the sealing edge with the top on the windscreen. Any suggestions on other seals etc? Don't really want to put another britpart one in now.
  2. I'll be adding 1 ton shackles in the rear to account for the lift. The change in pinion angle should also help with my slight gearbox/pinion misalignment on the rear axle. Most likely I'll end up with paras in the back some day, but it's an extra $1000 NZD for the rears and my budget at the moment just can't justify it.
  3. Thanks for the advice guys Think I'll just order fronts and if it turns out to be an issue I'll bite the bullet and buy a set of rears as well. Not going to be carrying lots of weight the whole time but it is a lwb flatdeck ute (pickup) living on a farm so its likely to be loaded up a bit. Not as much as its previous life as a fencing truck though, the cracked tray mounts and chassis said that it may have carried a fair bit more than its payload at times!
  4. I'm thinking of running front parabolics while keeping the rear springs standard with extended shackles. I want to keep the rear springs standard for a few reasons, load carrying ability being one of them as well as parabolics being quite expensive to ship to the other side of the world (NZ), so shipping only two springs will keep the costs down considerably. Does anyone have any experience of mixing paras and normal springs? I'm just wondering if there's any adverse handling effects that I haven't thought of. Cheers
  5. Just the info I needed, thanks.
  6. While I’m rebuilding my 63 series 2a Ute I’ve decided to upgrade to boosted dual line brakes. I’ve done all the brake pipes but I’m a bit stuck on the master cylinder unions. Firstly, does the bigger union go to the front or back? And does it use a larger line as well? The brake lines I’ve made are 3/16 pipe. Also does anyone know the specs of the larger union? I’ve had a hard time finding one locally (NZ). Cheers
  7. The wipers on my 200tdi disco have stopped parking and working on intermittent. I'm thinking its the park switch. Does anyone know if the park switch is replaceable separately or do I need a new motor assembly. I think the 200tdi motor is different to a 300tdi because all the ones i've seen online are for 94-99. Might be the same as a RRC? Any help appreciated
  8. I've got a 94 200tdi Discovery that has a leaking screen. Does anyone have the part number for the windscreen seal? I seem to remember that later D1s have a different seal and i'm not sure if the ones i'm seeing online are the right ones. The photo is the seal thats currently in there. Cheers
  9. I'm going to be respraying my 63 2a soon. Just wondering how much I will roughly need to spray a 109 chassis cab. I'll be doing everything off the car, so not just a shut door respray. Cheers
  10. I'm currently rebuilding my series 2a and i'm starting to sort out the wiring. It has a Holden 173 in it, a common conversion in these parts. I was wondering if I can delete the voltage regulator box on the bulkhead as it has an alternator instead of the original dynamo. I have always understood that the alternators have a sort of internal regulator so it is not needed.
  11. @Chicken Drumstick I'll probably just use a 3.9 out of a discovery but convert to carbs and maybe put a cam in it. Ideally once I have enough funds etc I really want a 4.6 or even a 4.4 out of a leyland p76 (aussie and nz model). Somewhere around 225-250hp which is roughly what a stock 4.6 puts out I think. A series box wouldn't be too keen on 4 times the original power going through it but by the sounds of it a LT95 might be up to it. I want to do the hard work now so when I come to maybe upgrading the engine I don't have worry about the gearbox. Also, surely the rear axle would never stand up to that sort of power so the logical option is full time 4wd so the power is split. Therefore the LT95 is a good option. I would just use a stage one front axle which are pretty easy to find here due to all the ex army trucks. As for the parabolics how are the rocky mountain springs? I've heard very mixed opinions on them. They also seem a bit pricey compared to other makes although they do come as kits with shocks. Thats a nice series you've got there. I'm pretty interested in your power steering setup. How hard is it and does it get rid of some of the series steering play?
  12. Hi all first time poster here! Planning on putting my 69 series 2a back on the road and I want to put a rover v8 in it. I am also keen on a LT95 box because i've heard that they're strong and I don't want to be constantly afraid of the series box blowing up when I plant my foot! I want to keep the standard look. I would use a 101 layshaft and bell housing to shorten the assembly 4". I also want parabolics which would lift the car a bit and make the rear prop angles even worse which I think is my main problem. Its going to be used a fair bit offroad so I don't want binding UJs. Basically, will this set up work in an 88"? My other options are using a stage one front end but I'm not set on the look, or use the series box. Cheers
×
×
  • Create New...

Important Information

We use cookies to ensure you get the best experience. By using our website you agree to our Cookie Policy