fatforbes

Thanks for the reply. Is there any way of accessing the top side of the rear bolts? It looks like theres a couple of small panels in the pick up bed near the tailgate that could be removed? Thanks

Recently purchased a G-reg hi-cap 2.5td. When I bought it it only had a dribble of fuel in and when I got home an filled it started dripping from the tank. I can't see any damage because the cover is in the way. So I went to remove the tank and found 2(new and shiny) bolts at the front (engine) end of the tank and the back,where I thought there would be bolts are two blobs of weld?? I'm guessing this isn't normal? If I do manage to remove the tank and it needs replacing, is the tank on a hi-cap specifically made for a hi-cap or is it the same on a 110? Thanks

Just another quick question. I just jacked both rear wheels off the ground to check wheel bearings etc..and for some reason, even though the handbrake was on I could turn both wheels and the propshaft wasn't rotating? I'm pretty sure that it's a salisbury rear axle. I don't understand???

Thanks for the response. I'm only using the hi-cap to cart stuff about off road so I'm not looking to spend vast amounts of money, which might be the case looking at 200/300tdi engines on ebay. Is it worth thinking about a 2.5d engine? I also have a daihatsu fourtrak engine, but is that more complicated? Thanks

I've just purchased a g-reg 2.5td Defender high capacity and have a few questions. I find the engine seriously lacking power, any hill and it dies very quickly. Is this normal? and if not what common problems should I be looking for? I've been told the 2.5td is not a very good engine. I'm used to driving a 300tdi 90 so perhaps I was expecting too much. How difficult is it to convert to a 200 or 300tdi? Thanks

Just did some research and found that it's on ebay and finished tomorrow(wasn't told this), so it will probably make more than I'm willing to pay, bummer. Seller wasn't there but I think he wanted around £600. here it is http://cgi.ebay.co.uk/1983-LAND-ROVER-88-4-CYL-BLUE_W0QQitemZ250770466160QQcategoryZ29748QQcmdZViewItemQQ_trksidZp5197.m7QQ_trkparmsZalgo%3DLVI%26itu%3DUCI%26otn%3D3%26po%3DLVI%26ps%3D63%26clkid%3D7086602005820102327#ht_500wt_1156

Had a look at an A reg series today. It's a petrol, chassis is good had new outriggers, alternator,HT leads and front prop and it started straight away with no smoke. Bulkhead and doors have some corrosion but not too bad, front n/s wing is a bit battered and it doesn't have any MOT/tax. It has also has an overdrive (not sure if these are standard). Not sure how much the guy is asking yet so what should I offer for it?? Cheers

Having a bit of trouble with my 96 defender 300tdi. It's having some trouble starting, it takes 4 or 5 attempts to get it going, it sounds like it wants to go but instantly dies. I have checked all the glow plugs and only 1 needed replacing which I've done. It doesn't seem to matter if it's hot or cold. Any ideas?? I'm also having trouble with the steering. The steering box was leaking from what I think is the rack & pinion adjuster (big flat bladed screw driver fitting on the side of the box) so I removed it and put some PTFE tape on then put it back again but since I did that I can't get my steering right, It's either floaty and all over the road or feels like I've got cement in the steering system. The box is only 2 years old and it's a reconditioned one.

Cheers! will they fit on the alloys??

What size tyre can I fit on a standard disco1 alloy?? It's for a 90, I've currently got 7.50 R 16 avon rangemasters on standard rims but I'm gonna get some Bf goodrich AT that are a similar size to the 7.50 R16s, what is a similar sie that will fit on the alloys?? Thanks

Hello, I replaced my steering box 2 years ago with a reconditioned unit and it has already started leaking! It's leaking from the output shaft, how difficult is it to replace the seal or seals in situ?? And is there a guide on doing it anywhere?? Also, my difflock light hasn't been working so I've replaced the sensor but still no light?? I've also checked the dash light which is working fine..any ideas?? It's a 1996 300tdi 90. Cheers

The alloys will fit, the only other thing is that the tyres are tubed, does this matter?

oh yeah its for a '96 90!

This may be a stupid question! Ive got some avon rangemaster tyres but they're on very tired wheels, but ive also got some discovery1 alloys, will the tyres fit on the alloys??? tyres are 7.5R16.

A friend of mine is embarking on a project to change his 90 n-reg 300tdi engine for a P6 3.5L v8 engine. Has anyone got any experience of doing this? What problems are likely to occur?? I guess the engine mounts will have to be moved and a gearbox conversion plate is needed? Any help would really help before the project gets started, Many thanks