Richy B

Just found it :0) looks a fun job :0/ grease up me knuckles ready ,

Inside the car, kinda under the dash then ?? Thanks

Where s it please ?? I think. Mine has some issues, so going to replace it, so where abouts is it located on the vehicle please ?? It's a 51plate 90 CSW, thanks in advance for assistance ,

Air flow meter ?? Changed mine today

Sorted - good old Air flow meter !!! Roars like a kitten again now :0)

Hi all, I have a 51 plate 90' full size big intercooler, IRB remap and over boost box, single box stainless exhaust, egr removed, Anyhow, up to recently its been running fine, I was going on a long run the other week soni gave it a drink of wynns injector cleaner as a treat ( no problems at this point ) During this trip It started to sort of misfire, it hesitates and usually "clears" then revs through fine, it seems to be getting there most of the time now, the misfire is not worse but defo more frequent, I changed the injector loom about 2 years ago for the usual reasons, I have rechecked this and all clean, it has a ecu extender loom fitted also about 3 years ago with no issues, the ecu now sits behind the drivers head rest, changed the fuel filter a cople of days ago also, oil smells fine of the dip stick, and no coolant loss, doesn't appear to smoke any more or less than norm , fuel usage seems norm ( quite bad :0) ) So where shall I go from here please ??

Just ot back from a weekend on the plain - there many many red flags out ( as expected) but there were many many trucks, tanks,planes,helicopters ect to keep us entertained :0) we came a tossed a convoy of 42 "vehicles" some i had no idea what they were or what they might do !! So overall, a load we couldn't do but they kept is entertained to make up for it ,

P.s if you do it on a warm day it's easier to remove/refit the glass rubber seals

It's really quite simple, basically remove the glass, clean and stick the pads to the rear, and choose the best route to wire um up ,I used a carling switch and a relay to be sure, I'm very happy with mine and have been there a few years now, very good in frosty days and also misty mornings

Evening all, I'm after some towing mirrors for my 90' I have had a look around some shops and online but nothing seems to look like it will fit ?? I tow a caravan and just need some extra width to see down the sides , ifi had a choice I would like removable ones as we usually go away with caravan then green laning In between, Thanks in advance

50.8 they are , so yea- maybe 2" I should of pressed the converter button on the vernier calliper :0) They are terrafirma flanges

And if anyone can reccomended a tool to add metal I'm up for it ;0) just kidding matey :-)

Got a 52 mm hub socket, which does the job, but just wanted one to fit "properly" and the fact i am a bit of a magpie on tools :0D

Where I get one please ?? Can only find 3/4 or 1" drive in sockets, I was after a 1/2 drive, it's for h/duty drive flanges caps, so ot super tight or nout, Thanks in advance

Tray back it !!!!!!!!! Only kidding ! Wifey and I were thinking about having a punt on it , but can't see if it's worth. Our time - ie the bidding goes way over that ?? That's the gamble though I guess :0/

We went today ( Saturday ) gotta be said I really enjoyed it, seemed more than busy enough, ok some of the big names weren't there, but I wasn't really shopping , although did buy a good selection of workshop consumables :0) and did a deal on a sky tag tracker jobby, Think the weather was a bonus for sure, Dunno what the traders till will say but most people were wandering round with somthing in a bag ,

We used a 90 puma for towing the challenge truck around the country last couple of seasons, does the job fine, Especially after we had the ecu tweaked :0) but was more than capable in std trim

Almost definitely were, kimi (co driver ) has a stiff neck today though ,

I believe Paul Bass is possibly out today, rolled @40mph ! Truck is messy :0( but both occupants ok :0) I have a pic buy can't seem to load it from me iPad ?

Prop u/j ??

O/side drivers front brake caliper , vented disc, ABS, to fit a 08 reg puma 90 station wagon, I have seen um on e Blag but look sooooo cheap £35 ish rebuilt ?!?!? That I'm guessing it's @hitpart or similar :0/ The truck s of a proper jolly soon and would never risk brake quality, Any idea of the genuine part no please so I can trawl further afield :0) Thanks in advance

Nope, only changed the pads for a pre morocco trip :0/

Himall, just fitted new mintex front n rear pads to a 08reg puma (with ABS) all fine and pistons pushed back easy enough, on test drive pedal feels real spongey, not at all like the sharp pedal it had before, it had very small lips on the outer edge of the disc which I linished off, Drove about 5miles ish so far but no real difference :0/ anything I've missed ya reckon ?? Maybe somthing to do with ABS ?? Any tips please ??

Oops !! Always forget that bit :0) I'm in Oakley, Hampshire, (Nearest big town is Basingstoke ) I don't mind paying a proper price and postage or adoration to the forum if that tips the scales ?? Thank you

Hi there, I require 4x 30mm diameter steel round bar with 10mm drilled n tapped holes in each end of the bar to a depth of 25mm , length 11 cm these are for a rear storage build in a 90 ( pics when finished ) can anyone on here build them for a sensible fee please ???? Many thanks