Jump to content

Simon B

Settled In
  • Posts

    236
  • Joined

  • Last visited

Everything posted by Simon B

  1. Haven’t Kahn or the Chelsea Truck Co been catering for these poor misunderstood but highly valued individuals for some time now? I have a 1990 v8 110 CSW with original engine (in garden for some time) that could be used as a base vehicle, can someone start the bidding at £35k please?
  2. Had a look about for tips on this and drew a blank, so, is there a method of adjusting your windscreen jets without the fluid hitting the wipers. Can anyone post a nifty diagram for the target area of the jet?
  3. I think the Isuzu options were; 4JB1T. 2.8 4 cylinder OEM in Aussie defenders at one point 4JG2 3.1 4 cylinder indirect injection. 4BD1 3.9 4 cylinder direct injection with or without turbo. Fitted I think to some Aussie discos and the military Perentie. I have a 2.8 in my 110, it is a very smooth engine, also used in Vauxhall Frontera. I thought about the 3.9 but had heard it could shake your fillings loose at idle. There was also a rumour that Isuzu produced a small number of 4JB1Ts that were bored out to 3.1 just before they went indirect injection. That might be a very nice power plant.
  4. Changed the lock and switch, it was the el cheapo switch module on the end, is this a spare to save me the effort next time? Held on by a rubbish miniature Philips screw.
  5. Its the issue of the switch burning itself out each time, the heater motor seems to draw 4 amps but its a thin gauge wire and isn't brown or brown with an orange trace. It appears to be white with an orange or red trace? When I replace the ignition switch and lock I'll take my fuse box off the bulkhead and check the wire colours on either side of the fuse
  6. They’ve always been the questionable quality Lucas part. What I don’t quite get is why the v8 is the only model that gets the heater motor off it?
  7. Ive studied the various threads and about the above but not seen a similar fault. Every 3-5 years I have to replace my ignition switch/lock . Its a 1990 v8, all the circuit diags show a wire from the ignition to the fuse box then to the heater motor. On all the failed ignition switches its this terminal that appears to melt, the back of the switch gets all loose and wobbly then you have to change it. The wire itself to the fuse box seems pretty thin gauge, though it never blows the fuse the fuse itself is also a touch on the brown singed looking side. Anyone else seen this fault, I'm tempted to run a new wire in to the fuse box from a better switched feed.
  8. Earth (black) now on correct stud Gauge (green/black) now on white terminal Warning light (white) yet to be connected to red terminal My gauge was trying to read the warning light supply, whilst earthing through gauge terminal. It appears to be working ok, will recable it properly with a cable to the warning light when the stuff comes from VWP.
  9. Western, Is it threaded or is there some sort of crimp thingy I need to get for it? A female bullet?
  10. That may be something similar to my symptoms. I think the black wire should go to the threaded post. Not the white terminal. I'll test this when it stops raining. I think the white terminal is for the low fuel light.
  11. This driving me a bit mad, fitted a new tank at the back, had to run in new wires. Connected up and tank read fine when not moving. Had it for a bit of a drive and reads empty unless I'm turning right. Fuel level is actually full. Hoping it isn't a sender fault and is a wiring fault i can trace out.
  12. I ran with a twin set up under passenger seat, they fit well. After I fitted the diesel went down to one big one. Then keep spare charged and in a box in case I need to do a remote jump start, a lot easier than trying to park close.
  13. I think I have a pair of Disco Efi manifolds, they were alleged to be better than the std 3.5 LR ones think they go 2-1 then out rather than 4-1 let me know. Also got a complete engine but it's been outside for years so may have seized. Sorry chaps.
  14. If it's for regular use, get a kit that puts the hitch at standard trailer height. The bumper is a tad too high, you'll notice more with a long trailer and uneven ground. I love mine, by Watling Eng. the only downside is you need to practice reversing a trailer now and then. I use mine to launch my clubs 6.8m dive boat, safe and easy to see hazards etc. Do it! Do it now!
  15. Talked to NFU today, sounds like a bad postcode, I'll talk to Heritage tomorrow.
  16. Funny you should say that, NFU, I live in Leicester. It does have an Isuzu 2.8 in it so is "modified"
  17. Just had my renewal, 50 year old bloke, 8 years plus NCD, 25 year old 110 CSW. £868 Anyone one else had similar?
  18. Cool, can you get NOS out of a pump at the garage? Portal Rover used to do the kits but they appear to have disappeared.
  19. I was curious, if I went for it it would be for a bit more performance say when towing and a cleaner burn so its a bit greener.
  20. This was a hot topic a while back, does it get done any more? If not why not? Cost? or wrecking the engine?
  21. Hello, Whenever I change gear my gearbox makes a weird noise, a bit like a large dog whimpering, it only happens when I press the clutch in or let it out. I had discounted thrust bearing as it isn't there if there is light pressure on the clutch. Input bearing on gearbox has been mentioned, its a split santana box originally from a V8 fitment. Any ideas on how long it will be before it might let go?
  22. I bought some XL sized mirrors from Craddocks, very nice but more susceptible to wind, I too also tightened up to the max, I'll try the jubilee clip mod! Wonder if even a cable tie would work, might test this.
  23. Sound advice and its a bit cold to be outside with a dial gauge. Did an airport run yesterday, 160 miles. Going there (supermarket glug diesel) 30mpg coming back BP Ultimate Rocket juice 32 mpg. Might run this type of fuel more often.
  24. Economy has indeed improved, still sounds a little soft so I may try 10 degrees BTDC unless people think this is a bad idea. Also just fitted a gas strut door stay kit... Why oh why did I not do this years ago. Work light next.
×
×
  • Create New...

Important Information

We use cookies to ensure you get the best experience. By using our website you agree to our Cookie Policy