Gazzar Posted October 29, 2017 Share Posted October 29, 2017 I've taken the overdrive out of the Landrover. It was getting noisy, so, as I've a long trip with the trailer, I thought it was best to take out the weak link. This was the lock plate. Not good. The main clutch looked good, so hopefully all the overdrive needs is a new set of bearings. What are overdrives making these days? The plan is to fit a high ratio transfer box one of these days. G. Quote Link to comment Share on other sites More sharing options...
jordan_meakin Posted October 29, 2017 Share Posted October 29, 2017 If your question is simply what price are second hand overdrive units making, then usually above £300. Quote Link to comment Share on other sites More sharing options...
Gazzar Posted October 30, 2017 Author Share Posted October 30, 2017 My question was more around what caused that lock tab plate to fail! The nut was not very tight either. I suppose the concern is that I torqued that correctly and still it failed. Interesting on the price of the overdrive, though. I've now got two spare. G. Quote Link to comment Share on other sites More sharing options...
David Sparkes Posted October 30, 2017 Share Posted October 30, 2017 The nut that was not very tight, that's the conical castellated nut that requires a special socket, isn't it? If so, do you have a special socket, bought or home made? If the nut wasn't very tight the first question has to be 'was it torqued correctly?'. I'm not sure if a home-made socket might be able to jam against something, and so appear tight before the nut is as tight as required. I appreciate questioning what you have done might seem impolite, but I think the question has to be asked, not just 'thought'. Regards. Quote Link to comment Share on other sites More sharing options...
Gazzar Posted October 30, 2017 Author Share Posted October 30, 2017 No, it's cool. It's fair to question. The socket was a home made filed to fit deep socket, it fits nicely. The nut was torqued to and then some, so the lock tabs lined up. Serious strain on the breaker bar. I'm wondering if it was too tight? I'm dismantling another box at the moment, a series 2a factory recon box, and the main nut was not nearly as tight, once the tabs were folded back the nut came off by hand. I'll check it in a couple of weeks time, after 500 miles. Thanks, G. Quote Link to comment Share on other sites More sharing options...
David Sparkes Posted October 30, 2017 Share Posted October 30, 2017 44 minutes ago, Gazzar said: ... The nut was torqued to and then some, so the lock tabs lined up. Serious strain on the breaker bar. I'm wondering if it was too tight? ... Just checked the instructions, Fairey (Superwinch) specify 100 lbf-ft for the nut. I thought I had read that this is more that LR specify for a standard build, but looking in the S3 workshop manual, no figure is specified. Regards. Quote Link to comment Share on other sites More sharing options...
Gazzar Posted October 30, 2017 Author Share Posted October 30, 2017 Thanks David, I recall the torque was much more than this. Something from the 2a manual? Perhaps too much? G. Quote Link to comment Share on other sites More sharing options...
secondjeremy Posted October 31, 2017 Share Posted October 31, 2017 The only torque figure for that nut is that in the overdrive instructions. There is none given in any of the series workshop manuals. The nut frequently works loose! Quote Link to comment Share on other sites More sharing options...
Snagger Posted November 1, 2017 Share Posted November 1, 2017 The trouble is that the locking tabs rarely align with the slots when tightened to the correct 100'Lb, so you need to adjust the nut a little in one direction or the other, affecting that torque. If it is missing from the LR manuals, that may be why. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.