Anderzander Posted November 6, 2022 Share Posted November 6, 2022 Waffley Versatile … 🎶 Quote Link to comment Share on other sites More sharing options...
landroversforever Posted November 7, 2022 Share Posted November 7, 2022 I take it back Stephen, that looks great! 1 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 6 minutes ago, landroversforever said: I take it back Stephen, that looks great! That's very gracious of you Ross Thank you very much regards Stephen 1 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 How much drilling this morning really Pilot holes Punch holes Have to say I'm really not looking forward to punching all these out, needs must and all that regards Stephen Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted November 7, 2022 Share Posted November 7, 2022 Surprised you don't have some massive flypress that you picked up from a scrap man, with a throat big enough to accept the whole sheet in one... Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 12 minutes ago, Bowie69 said: Surprised you don't have some massive flypress that you picked up from a scrap man, with a throat big enough to accept the whole sheet in one... In an ideal world......... Regards Stephen Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted November 7, 2022 Share Posted November 7, 2022 Here's a thought..... what about polishing it when done? I'm not normally one for shiny, nor you I guess.... but could be a cool feature on the front end 1 Quote Link to comment Share on other sites More sharing options...
markyboy Posted November 7, 2022 Share Posted November 7, 2022 17 hours ago, Stellaghost said: Completed one of the side mesh panels, cleaned it up and gave it a bit of primer, agreed its not perfect but I think once painted green and on the vehicle it should look OK Thoughts please gents Regards Stephen I was a little sceptical at first. However, this changed my mind (should never have doubted you), that looks really good, more than acceptable in my humble opinion. 1 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 I'll just leave these here, 20mm plate Guesses welcome regards Stephen Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 8 minutes ago, Bowie69 said: Here's a thought..... what about polishing it when done? I'm not normally one for shiny, nor you I guess.... but could be a cool feature on the front end Think I will mull that over Regards Stephen Quote Link to comment Share on other sites More sharing options...
landroversforever Posted November 7, 2022 Share Posted November 7, 2022 13 minutes ago, Stellaghost said: I'll just leave these here, 20mm plate Guesses welcome regards Stephen Anyone else's place and a cursory glance would expect 8-10mm plate.... knew it would be something beefy for you Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 3 hours ago, markyboy said: I was a little sceptical at first. Me and you both regards Stephen 1 Quote Link to comment Share on other sites More sharing options...
CwazyWabbit Posted November 7, 2022 Share Posted November 7, 2022 3 hours ago, Stellaghost said: I'll just leave these here, 20mm plate Guesses welcome regards Stephen Drinks holder? 2 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 10 minutes ago, CwazyWabbit said: Drinks holder? Way off the mark Clue Following true to form Regards Stephen Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted November 7, 2022 Share Posted November 7, 2022 Another pair of dies? 1 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 11 minutes ago, Bowie69 said: Another pair of dies? Correct, but for what ??? Regards Stephen Quote Link to comment Share on other sites More sharing options...
Blanco Posted November 7, 2022 Share Posted November 7, 2022 Headlamp Panels? Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 27 minutes ago, Blanco said: Headlamp Panels? Nice try but no Regards Stephen Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted November 7, 2022 Share Posted November 7, 2022 Windscreen frame. Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 No Clue What am I making at the moment Less tig when I've done this Regards Stephen Quote Link to comment Share on other sites More sharing options...
Popular Post Stellaghost Posted November 7, 2022 Author Popular Post Share Posted November 7, 2022 Forgive the pun, I'm punch drunk ! Panel completed apart from cleaning up It's not perfect by any standard and not good enough to give it the Bowie69 bling factor, but I'm absolutely not making it again so it is what it is I'm afraid regards Stephen 5 Quote Link to comment Share on other sites More sharing options...
Anderzander Posted November 7, 2022 Share Posted November 7, 2022 7 minutes ago, Stellaghost said: No Clue What am I making at the moment Less tig when I've done this Regards Stephen Are you going to press your own front panel from 6mm ? If so .. you won’t need a bumper! Quote Link to comment Share on other sites More sharing options...
CwazyWabbit Posted November 7, 2022 Share Posted November 7, 2022 So they are for forming the front panel.... and a drinks holder 1 Quote Link to comment Share on other sites More sharing options...
CwazyWabbit Posted November 7, 2022 Share Posted November 7, 2022 BTW I'm amazed how well it's turned out, I was expecting it to stretch and distort a lot, but it looks like it's only had a little stretching in the big panel. 2 1 Quote Link to comment Share on other sites More sharing options...
Stellaghost Posted November 7, 2022 Author Share Posted November 7, 2022 18 minutes ago, CwazyWabbit said: So they are for forming the front panel.... and a drinks holder Yes, going to make formers to make the angled sides on the front panel then I only have the 4 corners to tig regards Stephen 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.