Jump to content
mad_pete

Lowest effort rx 8 seat fitting to 90

Recommended Posts

Okay ordered some RX 8 seats from eBay and then ordering some of these

https://www.edgegarage.co.uk/store/products/127044

And see what the lowest amount of work I can do to get these in. I’m not getting the loom so will be some plugging things because in 2 months it’s 2020 and the future is heated seats.

This is minimum effort so not planning to go near any box section so yes this is a total cheat for the fabrication section but maybe I need to take a bracket off the seat who knows.

 

Share this post


Link to post
Share on other sites

Like the idea - watching with interest pete.....  😎

 

Rover 800's in mine but rather a pair of them with no too much hassle!  😊

Share this post


Link to post
Share on other sites

Fitting them without those rails is relatively easy. The most time consuming bit was cutting off the RX8 mounts and wiring them up.

I used the original RX8 switches but ran them through a custom made fuse/relay center behind the passenger seat.

 

I think I've had my heated seat on every day since I fitted them 👼😂

Seat.jpg

FRC.jpg

Share this post


Link to post
Share on other sites

Looks very nice !

Would you mind sharing some pictures of the rest of the interior, please ?

Share this post


Link to post
Share on other sites

I was worried about the potential loss of leg room, but there doesn't seem to be much difference.

I cant put my seat back as far as possible due to my toolbox behind (the back of the seat hits it), but i'm 6ft and I can cope.

You can see the original RX8 heated seat switches on the bottom right of my centre console. I may change the switches in the future to match the rest of my switches, but they'll do for now.

console3.jpg

interior.jpg

interior2.jpg

console2.jpg

FRC2.jpg

Share this post


Link to post
Share on other sites

That is very nice looking. I may have some questions around that in a bit if I may. 

Mine remain low effort as my seat rails have not arrived. 

Seats have though and they look good. A lot of seat for the money. 

They have a car air fresher smell to them, which I hate so I might give them a go over with a steam cleaner and some leather polish. Maybe take a look at taking the air bags and seat belt clips out.

Share this post


Link to post
Share on other sites
On 12/1/2019 at 2:01 PM, mad_pete said:

That is very nice looking. I may have some questions around that in a bit if I may. 

Mine remain low effort as my seat rails have not arrived. 

Seats have though and they look good. A lot of seat for the money. 

They have a car air fresher smell to them, which I hate so I might give them a go over with a steam cleaner and some leather polish. Maybe take a look at taking the air bags and seat belt clips out.

Any questions, drop me a PM

Share this post


Link to post
Share on other sites
On 12/20/2019 at 12:05 PM, mad_pete said:

Still don’t have my rails.....

I used the original rails off my defender seats, stripped them down to the bare rails, same with the RX8 seats, and 'merged' them together  😄

It will all be worth it once you get them in, it's like driving a different car!

Share this post


Link to post
Share on other sites

Hope you don't mind some questions....

What "motherboard" it is you're you using, please ?

Is that a Mudstuff console ?

image.png.bf8f49f3dc20f8d8463d933f99eea7eb.png

and what is that panel on the dash ?

Radio ?

CB ?

Thanks

Share this post


Link to post
Share on other sites

Where the arrow is pointing is a Parrot handsfree. Next to the Parrot is the pin entry for the Sigma alarm.

The centre console I made myself from 1mm steel and then coated with  bed liner type material.

The panel with the switches on is from Amazon. It's a tidy way of housing the switches volt meter and 12v sockets.

The fuseboard is from a Volvo Truck (I work for Volvo, got this one handy out of the scrap bin).

 

CC1.png

CC3.png

CC5.png

Share this post


Link to post
Share on other sites

Thank You VERY Much !

Share this post


Link to post
Share on other sites

Okay I’m going to need to change the title. 10 weeks and still no rails from edge garage. All I have managed to get done is leave a lot of messages asking for updates....

Share this post


Link to post
Share on other sites

I’m now stuck with what to do. I asked for a refund (quite a bit now) but no response. The £90 is I think below the minimum credit card protection level which leaves small claims court I guess ? I want to go and get some mud rails and move this along but I don’t know if Edge will end up sending me the rails anyway.

I’m ready to be understanding for production and other issues but companies that promise update after update and then don’t ever give one are very frustrating to deal with. If you said a week but now it’s two just send me a text Surely that’s not too hard?

 

Come on Edge give me my money back !

🙂

 

 

Share this post


Link to post
Share on other sites

Edge is down the road from me, I imagine they ship the kits from overseas hence the delay.

 

they are a small workshop/garage set up.

Share this post


Link to post
Share on other sites

From what I can gather the rails are made to order and they have been sent back twice because of holes in the wrong places. Which okay maybe sort your supplier out but as soon as you know that please update me that my order is delayed.

i think they also run trips which seems to mean they shutdown for weeks at a time. I asked for the instructions  in December so I could get on and prep the seats and I haven’t got those and I was told I would get an update Friday/weekend and don’t have that and that’s pretty much how this has played out.

I looking at last week in November get these installed and now I’m thinking should I make a top gear like sofa with them for the garage in the meantime to stop me tripping over them....

Share this post


Link to post
Share on other sites

I don’t know the company other than driving past and seeing muddy trucks outside the building so can’t really comment but there has been some concerns lately about them.

 

facebook post yesterday regarding them doesn’t look good

 

i cant share here, I’ll pm you 

 

Share this post


Link to post
Share on other sites

Wow looks like someone’s whole Land Rover is missing.

I phoned my credit card company.
“Could I have my money back please as I don’t have any rails.”
“Yes certainly here it is”

”thanks that’s brilliant ”

so that’s all sorted 🙂

now I need to decide mud rails or experiment with box section.....

 

Share this post


Link to post
Share on other sites

Okay less moaning more doing stuff. First up air bags out. So removing the rx8 seat air bags.


C2D9A589-7E8A-4DEB-8ADC-3FA0E195D85B.thumb.jpeg.b2ffaea83162da612819f33d82703f90.jpeg

F59CD32A-887B-445A-B83B-B807B2FE2299.thumb.jpeg.18138e773c7a2d809bfe5d16b3cfe017.jpeg

B220DD9C-E02F-49B8-AC61-5C51E09D30DA.thumb.jpeg.5efe232728de6ae7379d90652ce6f5ee.jpeg

9AC070C9-4965-4DAA-B4B8-577572CD898C.thumb.jpeg.1c9e9aaa7f90fd09d6e68ad103b25b9f.jpeg

now I need to work out how to get the outside cover but not the explosive bit.

 

Share this post


Link to post
Share on other sites

Did you manage to separate the explosive part / gubbins of the air bag and leave the external trim piece to reinstall in the seat?  

 

I’ve currently disconnected mine in the seat base but will (at some stage) need to put the vehicle through an IVA test and think the man in the white coat may not look to favourably on the seats if they still contain the (disconnected) airbags...

 

 

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...

Important Information

We use cookies to ensure you get the best experience. By using our website you agree to our Cookie Policy