Tris Cocks Posted April 3, 2010 Share Posted April 3, 2010 As i wasnt sure if or when the timing belt had be changed i decided that it would be wise to change it as the mileage is about 72K. i changed the timing belt yesterday using the method described in les' How To section by removing the wire from the back of the injector pump. after changeing the belt i replaced evertything the same way it came off and the engine wont start. It turns over but doesnt fire, ive checked theres voltage going to the wire that was connected to the back of the injector pump, and also checked there is fuel coming out og the injectors but it still wont start. Any pointers of what to try next? Thanks Tris Quote Link to comment Share on other sites More sharing options...
white90 Posted April 3, 2010 Share Posted April 3, 2010 If you have fuel and voltage on the solenoid then timing out would be my suggestion. recheck what you have done. Quote Link to comment Share on other sites More sharing options...
elbekko Posted April 3, 2010 Share Posted April 3, 2010 Sounds familiar Your timing is one teeth off. Even when the timing pin is in, it'll still be one teeth off after tightening. So the trick is to set it wrong just right Quote Link to comment Share on other sites More sharing options...
Tris Cocks Posted April 3, 2010 Author Share Posted April 3, 2010 Sounds like i will be taking it back out tomorrow and starting again. Elbekko - when you say set wrong just right it sounds as clear as mud, which way does the one tooth have to be out? Quote Link to comment Share on other sites More sharing options...
white90 Posted April 3, 2010 Share Posted April 3, 2010 Tris the best way I found was to make sure the Rad is out of the way so you can see properly and do it by the numbers follow the guide and all went well on mine anyway. Quote Link to comment Share on other sites More sharing options...
elbekko Posted April 3, 2010 Share Posted April 3, 2010 After tightening turn it around manually and recheck. Then you'll know what way you'll have to turn. And if it isn't a lot, the three bolts holding the pulley are in adjustable holes, so a bit of adjustement can be given that way without removing the belt. Oh, and don't worry, if you've done it once the second time is so much quicker Quote Link to comment Share on other sites More sharing options...
Tris Cocks Posted April 3, 2010 Author Share Posted April 3, 2010 I'll take the rad out while doing to tomorrow as its not the easiest place to get to. Quicker the second time around - sounds like a man speaking from experience. Is it a stupidly daft idea to try the engine to see if it starts with the timing cover removed? Quote Link to comment Share on other sites More sharing options...
western Posted April 3, 2010 Share Posted April 3, 2010 I'll take the rad out while doing to tomorrow as its not the easiest place to get to. Quicker the second time around - sounds like a man speaking from experience. Is it a stupidly daft idea to try the engine to see if it starts with the timing cover removed? you can do that, but only for a very short time as with the rad out there will be no coolant & no water pump so the engine will get hot very quickly. Quote Link to comment Share on other sites More sharing options...
T1G UP Posted April 3, 2010 Share Posted April 3, 2010 wouldn't hurt just to check starting Quote Link to comment Share on other sites More sharing options...
elbekko Posted April 3, 2010 Share Posted April 3, 2010 Quicker the second time around - sounds like a man speaking from experience. Yeah, had it happen a few weeks ago... Now I'm on to bigger problems. When a TDi doesn't feel like working, it really doesn't feel like working apparently. Quote Link to comment Share on other sites More sharing options...
white90 Posted April 3, 2010 Share Posted April 3, 2010 Definatley ok to start it with the cover off just keep it short and make sure everything that should be tight is and pins removed Quote Link to comment Share on other sites More sharing options...
Les Henson Posted April 4, 2010 Share Posted April 4, 2010 It is quite difficult sometimes to get the belt nice and taught between the cam and crank sprockets and it's common to accidentally put the cam sprocket one tooth out when fitting it. This why you rotate the engine 2-turns clockwise after fitting the belt and then re-check the timing. You can start the engine with the cover off and I do it every time - just to make sure. Reconnect the fuel solenoid wire, start the engine and briefly rev it. If it starts and revs ok, then the jobs a good-un Les. Quote Link to comment Share on other sites More sharing options...
steve b Posted April 4, 2010 Share Posted April 4, 2010 .......if the rad is out then your engine oil heat exchanger pipes will be disconnected so if you start it you'll dump all your engine oil . My guess is the cam is out as the arrow is not easy to see , using a small mirror to get a direct line of sight helps cheers Steveb Quote Link to comment Share on other sites More sharing options...
Tris Cocks Posted April 4, 2010 Author Share Posted April 4, 2010 Well congratulations on identifying problem. The crank was one tooth out when after i set the correcct tension on the belt. Elbekko, Your definately right about it being easier the second time around etc Quote Link to comment Share on other sites More sharing options...
white90 Posted April 4, 2010 Share Posted April 4, 2010 .......if the rad is out then your engine oil heat exchanger pipes will be disconnected so if you start it you'll dump all your engine oil . My guess is the cam is out as the arrow is not easy to see , using a small mirror to get a direct line of sight helps cheers Steveb I considered it obvious to put the rad back in but I did miss it from the post above Quote Link to comment Share on other sites More sharing options...
T1G UP Posted April 4, 2010 Share Posted April 4, 2010 when i did my 200 i lifted the oil cooler still connected up out the way. Took the rad out the frame etc but didn't want to undo the oil side of things. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.