Arsene Posted May 25, 2010 Share Posted May 25, 2010 Hi all. I have recently had problem with my 1995 Range Rover Classic 4.2L LWB. For some reason it wouldn't start so I took it to mechanic. He checked the fuel pressure, which was ok, then he checked the fuel injector relays under the dash of passenger side, he replaced one of relays, and finally he checked the fuses under hood, and 15A fuse was burned out. After replacing fuse the Rangie came back to life. But what happened next was that the idling would be unstable, jumping up and down, you could smell that the fuel was running rich, and fuel consumption increased by 50%. Also the truck lost his power while accelerating. I would appreciate if anyone of gurus could list the possible causes of: 1.Cause of increasing of fuel consumption 2.Why engine is running rich 3.Unstable idling. 4.Loss of engine's power Any input would be greatly appreciated. Cheers. Arsene. Quote Link to comment Share on other sites More sharing options...
DC_ Posted May 25, 2010 Share Posted May 25, 2010 Sounds like it could be your CTS ( coolant temp sensor) It'll not realise your engine is heating up and still throw lots of fuel in therefore giving the impression of overfuelling. It above your thermostat housing. Contact plug connected to it. Unscrew and fit a new one. Quote Link to comment Share on other sites More sharing options...
DC_ Posted May 25, 2010 Share Posted May 25, 2010 http://www.paddockspares.com/pp/RANGE%5FROVER%5F1986%2D1994/Engine%5FParts/Water%5Ftemperature%5Fsensor%5Fto%5FECU%5F%2D%5F3%2E9%5FV8%5FEFI.html Use the part number to search on google etc. You might be able to get one posted cheaper or take it to your local stealer Quote Link to comment Share on other sites More sharing options...
ThreeSheds Posted May 25, 2010 Share Posted May 25, 2010 Possible that the ECU had detected the fault and gone into limp-home mode. This can be reset by turning off the ignition and then disconnecting the battery for 15 seconds. Make sure you know how to reset the radio before doing that though... Quote Link to comment Share on other sites More sharing options...
Arsene Posted May 26, 2010 Author Share Posted May 26, 2010 Thanks everyone for your help. I will try and let you know. Thanks again. I really appreciate it. Cheers. Arsene. Quote Link to comment Share on other sites More sharing options...
vougese39 Posted May 31, 2010 Share Posted May 31, 2010 14 cux does not have a limp home mode!!!! coolant temp sensor only use genuine or afm but really need to read ecu faults Quote Link to comment Share on other sites More sharing options...
ThreeSheds Posted June 1, 2010 Share Posted June 1, 2010 14 cux does not have a limp home mode!!!! coolant temp sensor only use genuine or afm but really need to read ecu faults Apologies for misleading information then - it is not always easy to find definitive facts on the 14CUX and since I have read in several places, words to the effect of (quoting some of them)... www.v8forum.co.uk: "There are six fuelling maps in a 14CUX, one limp-home and five dedicated to a type of engine, i.e. 3.9/4.2, cat or noncat" www.g33.co.uk : "The device itself contains multiple maps, such as catalyst, non catalyst, limp home, and some country specific ones for particular fuels." RPi: (www.v8engines.com): "By the way, the default (Limp Home) tune is a cat map, so this usually makes a non-cat car run very rich." www.jpurnell.com: "Land Rover systems utilise LOS (or "limp-home mode"). When particular faults are identified, the ECM implements LOS using programmed default values rather than sensor signals. This allows the vehicle to be driven to a test and repair site. Once the fault is cleared, the ECM reverts to normal operation." ...I had thought that this was the case. Shows how easily one can be mislead by the internet! Roger Quote Link to comment Share on other sites More sharing options...
Ally V8 Posted June 1, 2010 Share Posted June 1, 2010 Was it the fuel pump relay that was replaced ? If it was then check its the right one,the centre pin provides a feed to the Oxygen sensors.If this is not working correctly then you will get overfuelling as described and a lumpy idle. Quote Link to comment Share on other sites More sharing options...
vougese39 Posted June 1, 2010 Share Posted June 1, 2010 well never told that when doing 14cux training! further more if in limp mode the ecu light will be on is it! if not then i can't be in limp mode never experienced one either. have just read some of the sites and it is not a true limp mode thus cannot really be called limp mode! and unless the waraning light is on you will never know Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.