kevindawes
-
Posts
59 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by kevindawes
-
-
From memory it was 5%, it was whatever Nige had set it to , I only changed it to zero when it was overdriving the injectors.
Tuning, I was the first time but after that I reloaded the base map and then didn't have the laptop connected and it still played up.
As it is now, for the first hour or short trips it runs great, good power and easily spins the wheels pulling out junctions and in the wet in a straight line. On the motorway it'll pull well for a good while and then gradually lose power until it misfires when you ask for some acceleration, a bit like a coil failing (I've already tried spare ones). It gets really bad once you pull off the motorway and back into normal traffic, eventually you have to stop of a minute and let it cool/reset and then it'll start ok and then run well enough to get you home.
On Saturday I'll spend some time getting some data logs created.
-
Nige, to be fair I've done that twice but I will do again as you suggest.
The basic tune ran my injectors at 80% after a few miles. It was suggested that I reduce the lambda authority to zero and that left me a vehicle that runs, albeit not perfectly but its where I am now.
I did have a blown exhaust but I've just had it completely refabricated so this will eliminate this as a problem.
-
Thanks to all your your comments.
Nige, in a post I made a few days ago (ego) I uploaded a log of when it was playing up.
Of course it could be my fuel pump or fuel regulator, both were fine before the conversion, and this only happens when the engine is hot.
What I did notice the other day was that while on the motorway the afr needle was way to the right all the time and then it started to progressively lose power. In traffic it barely ran. I turned it off opened the bonnet for a minute and reloaded the tune and it ran a lot better but not perfectly.
I'm running with the lambda authority to zero so it's not that effecting the afr.
My exhaust is new with no leaks so the lambda reading should be reliable now.
What should my air density correction be set to, air temp or coolant temp?
-
As some of you know if been been having trouble getting my ms install to work well. So far it's fine for about an hour and then starts losing power and becomes undrivable.
Reading around the forums it seems that my problem maybe heat soak effecting the inlet air temp sensor, it seems to tally up with the problems others have had although I don't have a particularly bad hot start problem.
I was wondering if I reloctaed the sensor from just after my air box to my snorkel I could alleviate the problem completely, or at least rule it out and narrow down my quest.
Pro's cons?
-
on a datalog, what would be typical expected values for Gego? Mine are min and max 100
-
Nige, could you load up the logs I sent you please?
Cheers
Kev
-
Nige, not sure. All the long runs I've had its been connected because I've been logging. Only on one run did i haventhe autotune running it went pair shaped sharpish. That resulted is a similar map to the one I ended up using the analyser in megaviewer with the second log I sent you using your spare ecu, it richened everything until it almost didn't run.
This weekend I'll load the base map and then run it without the laptop connected.
When the laptop is connected, is it actually doing anything unless its in autotune mode?
-
I didn't but I will, I'll send it to Bowie69 as he kindly offered to load it up for me as it was large.
I sent the two recent logs from nigels spare ecu to nigel and he's looking at them.
what was weird was that the second log when I loaded it into the megalog anaylser really richened the map just like the first one did with the original ecu.
when I load the base map, from nige, into megatune I get 20 warnings saved to audit.log, before it asks to burn to the ecu, is this normal?
It wouldn't let me uploud the file so I had to cut'n'paste it here
MegaTune - Startup file audit log
Install directory: C:/Program Files/MegaSquirt/MegaTune2.25
Working directory: C:/Program Files/MegaSquirt/MS1 Extra 029v
r megatune.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/megatune.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/megatune.ini
- C:/Program Files/MegaSquirt/mtCommon/megatune.ini
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/megatune.ini
r settings.ini
+ C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/settings.ini
settings.ini:0018 #group CODE_VARIANT
settings.ini:0019 unset DFI (false)
settings.ini:0020 unset DUAL_TABLE (false)
settings.ini:0021 unset MSNEDIS (false)
settings.ini:0022 unset MSNEDISmod (false)
settings.ini:0023 unset MSNS (false)
settings.ini:0024 set MSNS_EXTRA (true)
settings.ini:0025 unset MS_ECU (false)
settings.ini:0026 unset MS_I (false)
settings.ini:0027 unset MS_II (false)
settings.ini:0028 unset PIC_SQUIRT (false)
settings.ini:0029 unset GPIO (false)
settings.ini:0036 #group IDLE_CONTROLLER
settings.ini:0037 unset FIDLE_GAUGE (false)
settings.ini:0038 set PWM_GAUGE (true)
settings.ini:0039 unset IAC_GAUGE (false)
settings.ini:0047 #group LAMBDA_SENSOR
settings.ini:0048 set NARROW_BAND_EGO (true)
settings.ini:0049 unset WB_1_0_LINEAR (false)
settings.ini:0050 unset AEM_LINEAR (false)
settings.ini:0051 unset AEM_NON_LINEAR (false)
settings.ini:0052 unset DIYWB_NON_LINEAR (false)
settings.ini:0053 unset DYNOJET_LINEAR (false)
settings.ini:0054 unset TECHEDGE_LINEAR (false)
settings.ini:0055 unset INNOVATE_1_2_LINEAR (false)
settings.ini:0056 unset INNOVATE_0_5_LINEAR (false)
settings.ini:0057 unset INNOVATE_LC1_DEFAULT (false)
settings.ini:0058 unset ZEITRONIX_NON_LINEAR (false)
settings.ini:0059 unset WB_UNKNOWN (false)
settings.ini:0062 unset LAMBDA (false)
settings.ini:0066 #group Fueling_Algorithm
settings.ini:0071 set SPEED_DENSITY (true)
settings.ini:0072 unset ALPHA_N (false)
settings.ini:0073 unset AIR_FLOW_METER (false)
settings.ini:0076 set CELSIUS (true)
settings.ini:0081 set COLOR_24_BITS (true)
settings.ini:0083 set KPa (true)
settings.ini:0085 #group MAP_SENSOR
settings.ini:0086 unset MPX4115 (false)
settings.ini:0087 set MPX4250 (true)
settings.ini:0092 unset MPXH6300A (false)
settings.ini:0093 unset MPXH6400A (false)
settings.ini:Close
r colorScheme.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/colorScheme.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/colorScheme.ini
- C:/Program Files/MegaSquirt/mtCommon/colorScheme.ini
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/colorScheme.ini
colorScheme.ini:0001 unset BRADS_COLORS (false)
colorScheme.ini:0034 #if COLOR_24_BITS, including=true
colorScheme.ini:0065 #else, including=false
colorScheme.ini:0077 #if BRADS_COLORS, including=false
colorScheme.ini:0105 #else, including=false
colorScheme.ini:0133 #endif, including=true
colorScheme.ini:0135 #endif, including=true
colorScheme.ini:Close
megatune.ini:0023 #if DFI, including=false
megatune.ini:0025 #elif DUAL_TABLE, including=false
megatune.ini:0027 #elif MSNEDIS, including=false
megatune.ini:0029 #elif MSNEDISmod, including=false
megatune.ini:0031 #elif MSNS, including=false
megatune.ini:0033 #elif MSNS_EXTRA, including=true
r MSnS-extra.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/MSnS-extra.ini
+ C:/Program Files/MegaSquirt/MS1 Extra 029v/MSnS-extra.ini
MSnS-extra.ini:0018 unset MEMPAGES (false)
MSnS-extra.ini:0019 unset LOGPAGES (false)
MSnS-extra.ini:0021 #if MEMPAGES, including=false
MSnS-extra.ini:0032 #elif LOGPAGES, including=false
MSnS-extra.ini:0040 #else, including=true
MSnS-extra.ini:0048 #endif, including=true
MSnS-extra.ini:0082 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0083 #if MPXH6300A, including=false
MSnS-extra.ini:0085 #elif MPXH6400A, including=false
MSnS-extra.ini:0087 #else, including=true
MSnS-extra.ini:0089 #endif, including=true
MSnS-extra.ini:0091 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0094 #elif ALPHA_N, including=false
MSnS-extra.ini:0096 #endif, including=true
MSnS-extra.ini:0099 #if CELSIUS, including=true
MSnS-extra.ini:0101 #else, including=false
MSnS-extra.ini:0103 #endif, including=true
MSnS-extra.ini:0133 #if CELSIUS, including=true
MSnS-extra.ini:0135 #else, including=false
MSnS-extra.ini:0137 #endif, including=true
MSnS-extra.ini:0145 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0146 #if MPXH6300A, including=false
MSnS-extra.ini:0148 #elif MPXH6400A, including=false
MSnS-extra.ini:0150 #else, including=true
MSnS-extra.ini:0152 #endif, including=true
MSnS-extra.ini:0154 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0158 #elif ALPHA_N, including=false
MSnS-extra.ini:0160 #endif, including=true
MSnS-extra.ini:0163 #if CELSIUS, including=true
MSnS-extra.ini:0165 #else, including=false
MSnS-extra.ini:0167 #endif, including=true
MSnS-extra.ini:0197 #if CELSIUS, including=true
MSnS-extra.ini:0199 #else, including=false
MSnS-extra.ini:0201 #endif, including=true
MSnS-extra.ini:0213 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0214 #if MPXH6300A, including=false
MSnS-extra.ini:0216 #elif MPXH6400A, including=false
MSnS-extra.ini:0218 #else, including=true
MSnS-extra.ini:0220 #endif, including=true
MSnS-extra.ini:0221 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0224 #elif ALPHA_N, including=false
MSnS-extra.ini:0226 #endif, including=true
MSnS-extra.ini:0240 #if CELSIUS, including=true
MSnS-extra.ini:0242 #else, including=false
MSnS-extra.ini:0244 #endif, including=true
MSnS-extra.ini:0247 #if MPXH6300A, including=false
MSnS-extra.ini:0250 #elif MPXH6400A, including=false
MSnS-extra.ini:0253 #else, including=true
MSnS-extra.ini:0256 #endif, including=true
MSnS-extra.ini:0337 #if MPXH6300A, including=false
MSnS-extra.ini:0342 #elif MPXH6400A, including=false
MSnS-extra.ini:0347 #else, including=true
MSnS-extra.ini:0352 #endif, including=true
MSnS-extra.ini:0365 #if MPXH6300A, including=false
MSnS-extra.ini:0367 #elif MPXH6400A, including=false
MSnS-extra.ini:0369 #else, including=true
MSnS-extra.ini:0371 #endif, including=true
MSnS-extra.ini:0388 #if MPXH6300A, including=false
MSnS-extra.ini:0390 #elif MPXH6400A, including=false
MSnS-extra.ini:0392 #elif KPa, including=true
MSnS-extra.ini:0394 #else, including=false
MSnS-extra.ini:0396 #endif, including=true
MSnS-extra.ini:0401 #if CELSIUS, including=true
MSnS-extra.ini:0406 #else, including=false
MSnS-extra.ini:0411 #endif, including=true
MSnS-extra.ini:0414 #if MPXH6300A, including=false
MSnS-extra.ini:0416 #elif MPXH6400A, including=false
MSnS-extra.ini:0418 #else, including=true
MSnS-extra.ini:0420 #endif, including=true
MSnS-extra.ini:0426 #if MPXH6300A, including=false
MSnS-extra.ini:0428 #elif MPXH6400A, including=false
MSnS-extra.ini:0430 #else, including=true
MSnS-extra.ini:0432 #endif, including=true
MSnS-extra.ini:0441 #if MPXH6300A, including=false
MSnS-extra.ini:0444 #elif MPXH6400A, including=false
MSnS-extra.ini:0447 #elif KPa, including=true
MSnS-extra.ini:0450 #else, including=false
MSnS-extra.ini:0454 #endif, including=true
MSnS-extra.ini:0460 #if MPXH6300A, including=false
MSnS-extra.ini:0462 #elif MPXH6400A, including=false
MSnS-extra.ini:0464 #elif KPa, including=true
MSnS-extra.ini:0466 #else, including=false
MSnS-extra.ini:0468 #endif, including=true
MSnS-extra.ini:0470 #if CELSIUS, including=true
MSnS-extra.ini:0472 #else, including=false
MSnS-extra.ini:0474 #endif, including=true
MSnS-extra.ini:0478 #if MPXH6300A, including=false
MSnS-extra.ini:0480 #elif MPXH6400A, including=false
MSnS-extra.ini:0482 #else, including=true
MSnS-extra.ini:0484 #endif, including=true
MSnS-extra.ini:0507 #if CELSIUS, including=true
MSnS-extra.ini:0509 #else, including=false
MSnS-extra.ini:0511 #endif, including=true
MSnS-extra.ini:0519 #if MPXH6300A, including=false
MSnS-extra.ini:0522 #elif MPXH6400A, including=false
MSnS-extra.ini:0525 #else, including=true
MSnS-extra.ini:0528 #endif, including=true
MSnS-extra.ini:0561 #if CELSIUS, including=true
MSnS-extra.ini:0563 #else, including=false
MSnS-extra.ini:0565 #endif, including=true
MSnS-extra.ini:0567 #if MPXH6300A, including=false
MSnS-extra.ini:0569 #elif MPXH6400A, including=false
MSnS-extra.ini:0571 #else, including=true
MSnS-extra.ini:0573 #endif, including=true
MSnS-extra.ini:0586 #if CELSIUS, including=true
MSnS-extra.ini:0589 #else, including=false
MSnS-extra.ini:0592 #endif, including=true
MSnS-extra.ini:0601 #if MPXH6300A, including=false
MSnS-extra.ini:0604 #elif MPXH6400A, including=false
MSnS-extra.ini:0607 #elif MPX4250, including=true
MSnS-extra.ini:0610 #else, including=false
MSnS-extra.ini:0613 #endif, including=true
MSnS-extra.ini:0673 #if MPXH6300A, including=false
MSnS-extra.ini:0677 #elif MPXH6400A, including=false
MSnS-extra.ini:0681 #else, including=true
MSnS-extra.ini:0685 #endif, including=true
MSnS-extra.ini:0690 #if CELSIUS, including=true
MSnS-extra.ini:0694 #else, including=false
MSnS-extra.ini:0698 #endif, including=true
MSnS-extra.ini:0732 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0733 #if MPXH6300A, including=false
MSnS-extra.ini:0735 #elif MPXH6400A, including=false
MSnS-extra.ini:0737 #else, including=true
MSnS-extra.ini:0739 #endif, including=true
MSnS-extra.ini:0740 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0743 #elif ALPHA_N, including=false
MSnS-extra.ini:0745 #endif, including=true
MSnS-extra.ini:0754 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0755 #if MPXH6300A, including=false
MSnS-extra.ini:0757 #elif MPXH6400A, including=false
MSnS-extra.ini:0759 #else, including=true
MSnS-extra.ini:0761 #endif, including=true
MSnS-extra.ini:0762 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0765 #elif ALPHA_N, including=false
MSnS-extra.ini:0767 #endif, including=true
MSnS-extra.ini:0784 #if CELSIUS, including=true
MSnS-extra.ini:0786 #else, including=false
MSnS-extra.ini:0788 #endif, including=true
MSnS-extra.ini:0791 #if MPXH6300A, including=false
MSnS-extra.ini:0793 #elif MPXH6400A, including=false
MSnS-extra.ini:0795 #else, including=true
MSnS-extra.ini:0797 #endif, including=true
MSnS-extra.ini:0802 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:0804 #elif WB_1_0_LINEAR, including=false
MSnS-extra.ini:0806 #elif WB_UNKNOWN, including=false
MSnS-extra.ini:0808 #elif AEM_LINEAR, including=false
MSnS-extra.ini:0810 #elif AEM_NON_LINEAR, including=false
MSnS-extra.ini:0812 #elif DIYWB_NON_LINEAR, including=false
MSnS-extra.ini:0814 #elif DYNOJET_LINEAR, including=false
MSnS-extra.ini:0816 #elif TECHEDGE_LINEAR, including=false
MSnS-extra.ini:0818 #elif INNOVATE_1_2_LINEAR, including=false
MSnS-extra.ini:0820 #elif INNOVATE_0_5_LINEAR, including=false
MSnS-extra.ini:0822 #elif INNOVATE_LC1_DEFAULT, including=false
MSnS-extra.ini:0824 #elif ZEITRONIX_NON_LINEAR, including=false
MSnS-extra.ini:0826 #else, including=false
MSnS-extra.ini:0830 #endif, including=true
MSnS-extra.ini:0834 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0835 #if MPXH6300A, including=false
MSnS-extra.ini:0837 #elif MPXH6400A, including=false
MSnS-extra.ini:0839 #else, including=true
MSnS-extra.ini:0841 #endif, including=true
MSnS-extra.ini:0842 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0845 #elif ALPHA_N, including=false
MSnS-extra.ini:0847 #endif, including=true
MSnS-extra.ini:0850 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:0852 #elif WB_1_0_LINEAR, including=false
MSnS-extra.ini:0854 #elif WB_UNKNOWN, including=false
MSnS-extra.ini:0856 #elif AEM_LINEAR, including=false
MSnS-extra.ini:0858 #elif AEM_NON_LINEAR, including=false
MSnS-extra.ini:0860 #elif DIYWB_NON_LINEAR, including=false
MSnS-extra.ini:0862 #elif DYNOJET_LINEAR, including=false
MSnS-extra.ini:0864 #elif TECHEDGE_LINEAR, including=false
MSnS-extra.ini:0866 #elif INNOVATE_1_2_LINEAR, including=false
MSnS-extra.ini:0868 #elif INNOVATE_0_5_LINEAR, including=false
MSnS-extra.ini:0870 #elif INNOVATE_LC1_DEFAULT, including=false
MSnS-extra.ini:0872 #elif ZEITRONIX_NON_LINEAR, including=false
MSnS-extra.ini:0874 #else, including=false
MSnS-extra.ini:0878 #endif, including=true
MSnS-extra.ini:0881 #if SPEED_DENSITY, including=true
MSnS-extra.ini:0882 #if MPXH6300A, including=false
MSnS-extra.ini:0884 #elif MPXH6400A, including=false
MSnS-extra.ini:0886 #else, including=true
MSnS-extra.ini:0888 #endif, including=true
MSnS-extra.ini:0889 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:0892 #elif ALPHA_N, including=false
MSnS-extra.ini:0894 #endif, including=true
MSnS-extra.ini:0928 #if MPXH6300A, including=false
MSnS-extra.ini:0931 #elif MPXH6400A, including=false
MSnS-extra.ini:0934 #else, including=true
MSnS-extra.ini:0937 #endif, including=true
MSnS-extra.ini:0971 #if CELSIUS, including=true
MSnS-extra.ini:0974 #else, including=false
MSnS-extra.ini:0977 #endif, including=true
MSnS-extra.ini:1027 #if CELSIUS, including=true
MSnS-extra.ini:1029 #else, including=false
MSnS-extra.ini:1031 #endif, including=true
MSnS-extra.ini:1052 #if SPEED_DENSITY, including=true
MSnS-extra.ini:1053 #if MPXH6300A, including=false
MSnS-extra.ini:1055 #elif MPXH6400A, including=false
MSnS-extra.ini:1057 #else, including=true
MSnS-extra.ini:1059 #endif, including=true
MSnS-extra.ini:1060 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:1063 #elif ALPHA_N, including=false
MSnS-extra.ini:1065 #endif, including=true
MSnS-extra.ini:1116 #if MPXH6300A, including=false
MSnS-extra.ini:1118 #elif MPXH6400A, including=false
MSnS-extra.ini:1120 #else, including=true
MSnS-extra.ini:1122 #endif, including=true
MSnS-extra.ini:1846 #if CELSIUS, including=true
MSnS-extra.ini:1858 #else, including=false
MSnS-extra.ini:1870 #endif, including=true
MSnS-extra.ini:1884 #if CELSIUS, including=true
MSnS-extra.ini:1897 #else, including=false
MSnS-extra.ini:1910 #endif, including=true
MSnS-extra.ini:2606 #if CELSIUS, including=true
MSnS-extra.ini:2608 #else, including=false
MSnS-extra.ini:2610 #endif, including=true
MSnS-extra.ini:2618 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2621 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2623 #elif ALPHA_N, including=false
MSnS-extra.ini:2625 #endif, including=true
MSnS-extra.ini:2632 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2634 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2637 #elif ALPHA_N, including=false
MSnS-extra.ini:2639 #endif, including=true
MSnS-extra.ini:2646 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2648 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2650 #elif ALPHA_N, including=false
MSnS-extra.ini:2652 #endif, including=true
MSnS-extra.ini:2659 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2661 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2663 #elif ALPHA_N, including=false
MSnS-extra.ini:2665 #endif, including=true
MSnS-extra.ini:2672 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2674 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2676 #elif ALPHA_N, including=false
MSnS-extra.ini:2678 #endif, including=true
MSnS-extra.ini:2683 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:2686 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2688 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2690 #elif ALPHA_N, including=false
MSnS-extra.ini:2692 #endif, including=true
MSnS-extra.ini:2696 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2698 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2700 #elif ALPHA_N, including=false
MSnS-extra.ini:2702 #endif, including=true
MSnS-extra.ini:2704 #elif WB_UNKNOWN, including=false
MSnS-extra.ini:2707 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2709 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2711 #elif ALPHA_N, including=false
MSnS-extra.ini:2713 #endif, including=true
MSnS-extra.ini:2717 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2719 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2721 #elif ALPHA_N, including=false
MSnS-extra.ini:2723 #endif, including=true
MSnS-extra.ini:2726 #elif DIYWB_NON_LINEAR, including=false
MSnS-extra.ini:2729 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2731 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2733 #elif ALPHA_N, including=false
MSnS-extra.ini:2735 #endif, including=true
MSnS-extra.ini:2739 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2741 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2743 #elif ALPHA_N, including=false
MSnS-extra.ini:2745 #endif, including=true
MSnS-extra.ini:2749 #else, including=false
MSnS-extra.ini:2752 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2754 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2756 #elif ALPHA_N, including=false
MSnS-extra.ini:2758 #endif, including=true
MSnS-extra.ini:2762 #if SPEED_DENSITY, including=false
MSnS-extra.ini:2764 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2766 #elif ALPHA_N, including=false
MSnS-extra.ini:2768 #endif, including=true
MSnS-extra.ini:2770 #endif, including=true
MSnS-extra.ini:2790 #if SPEED_DENSITY, including=true
MSnS-extra.ini:2792 #elif AIR_FLOW_METER, including=false
MSnS-extra.ini:2794 #elif ALPHA_N, including=false
MSnS-extra.ini:2796 #endif, including=true
MSnS-extra.ini:2853 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:2855 #else, including=false
MSnS-extra.ini:2857 #endif, including=true
MSnS-extra.ini:2859 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:2861 #else, including=false
MSnS-extra.ini:2863 #endif, including=true
MSnS-extra.ini:2875 #if MPXH6300A, including=false
MSnS-extra.ini:2877 #elif MPXH6400A, including=false
MSnS-extra.ini:2879 #else, including=true
MSnS-extra.ini:2881 #endif, including=true
MSnS-extra.ini:2894 #if CELSIUS, including=true
MSnS-extra.ini:2897 #else, including=false
MSnS-extra.ini:2900 #endif, including=true
MSnS-extra.ini:2910 #if CELSIUS, including=true
MSnS-extra.ini:2912 #else, including=false
MSnS-extra.ini:2914 #endif, including=true
MSnS-extra.ini:2946 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:2948 #else, including=false
MSnS-extra.ini:2952 #endif, including=true
MSnS-extra.ini:3088 #if CELSIUS, including=true
MSnS-extra.ini:3091 #else, including=false
MSnS-extra.ini:3094 #endif, including=true
MSnS-extra.ini:3099 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:3101 #else, including=false
MSnS-extra.ini:3103 #endif, including=true
MSnS-extra.ini:3120 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:3122 #else, including=false
MSnS-extra.ini:3126 #endif, including=true
MSnS-extra.ini:3211 #if CELSIUS, including=true
MSnS-extra.ini:3213 #else, including=false
MSnS-extra.ini:3215 #endif, including=true
MSnS-extra.ini:3218 #if NARROW_BAND_EGO, including=true
MSnS-extra.ini:3221 #elif ZEITRONIX_NON_LINEAR, including=false
MSnS-extra.ini:3224 #elif INNOVATE_LC1_DEFAULT, including=false
MSnS-extra.ini:3227 #else, including=false
MSnS-extra.ini:3230 #endif, including=true
r lambdaSensors.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/lambdaSensors.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/lambdaSensors.ini
- C:/Program Files/MegaSquirt/mtCommon/lambdaSensors.ini
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/lambdaSensors.ini
lambdaSensors.ini:0019 #if NARROW_BAND_EGO, including=true
lambdaSensors.ini:0025 #elif WB_1_0_LINEAR, including=false
lambdaSensors.ini:0031 #elif WB_UNKNOWN, including=false
lambdaSensors.ini:0037 #elif DIYWB_NON_LINEAR, including=false
lambdaSensors.ini:0043 #elif DYNOJET_LINEAR, including=false
lambdaSensors.ini:0049 #elif TECHEDGE_LINEAR, including=false
lambdaSensors.ini:0055 #elif INNOVATE_1_2_LINEAR, including=false
lambdaSensors.ini:0061 #elif INNOVATE_0_5_LINEAR, including=false
lambdaSensors.ini:0067 #elif INNOVATE_LC1_DEFAULT, including=false
lambdaSensors.ini:0077 #elif ZEITRONIX_NON_LINEAR, including=false
lambdaSensors.ini:0083 #elif AEM_LINEAR, including=false
lambdaSensors.ini:0089 #elif AEM_NON_LINEAR, including=false
lambdaSensors.ini:0094 #endif, including=true
lambdaSensors.ini:Close
MSnS-extra.ini:3234 #if MPXH6300A, including=false
MSnS-extra.ini:3239 #elif MPXH6400A, including=false
MSnS-extra.ini:3244 #elif MPX4250, including=true
MSnS-extra.ini:3248 #else, including=false
MSnS-extra.ini:3251 #endif, including=true
MSnS-extra.ini:3372 unset MSLVV_COMPATIBLE (false)
MSnS-extra.ini:3374 #if MSLVV_COMPATIBLE, including=false
MSnS-extra.ini:3404 #else, including=true
MSnS-extra.ini:3455 #endif, including=true
MSnS-extra.ini:Close
megatune.ini:0035 #elif MS_ECU, including=false
megatune.ini:0037 #elif MS_I, including=false
megatune.ini:0039 #elif MS_II, including=false
megatune.ini:0043 #else, including=false
megatune.ini:0046 #endif, including=true
r common.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/common.ini
- C:/Program Files/MegaSquirt/MS1 Extra 029v/common.ini
+ C:/Program Files/MegaSquirt/mtCommon/common.ini
common.ini:Close
r custom.ini
+ C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/custom.ini
custom.ini:0015 #if CELSIUS, including=true
custom.ini:0016 Celsius enabled.
custom.ini:0018 #else, including=false
custom.ini:0021 #endif, including=true
custom.ini:0031 #if MS_I, including=false
custom.ini:0053 #elif MS_II, including=false
custom.ini:0080 #else, including=true
custom.ini:0106 #endif, including=true
custom.ini:0110 unset AUTOMARK_LOGGING_FEATURES (false)
custom.ini:0111 #if AUTOMARK_LOGGING_FEATURES, including=false
custom.ini:0126 #endif, including=true
custom.ini:0140 unset ALTERNATE_BURST_MODE_SETTINGS (false)
custom.ini:0141 #if ALTERNATE_BURST_MODE_SETTINGS, including=false
custom.ini:0147 #endif, including=true
custom.ini:Close
megatune.ini:Close
interWriteDelay = 1
pageActivationDelay = 50
blockReadTimeout = 25
writeBlocks = off
r megatune.cfg
+ C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/megatune.cfg
Comm port = 1
Comm rate = 9600
Timer interval = 50
megatune.cfg:Close
r thermfactor.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/thermfactor.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/thermfactor.inc
- C:/Program Files/MegaSquirt/mtCommon/thermfactor.inc
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/thermfactor.inc
thermfactor.inc:Close
r matfactor.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/matfactor.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/matfactor.inc
- C:/Program Files/MegaSquirt/mtCommon/matfactor.inc
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/matfactor.inc
matfactor.inc:Close
r NBafr100.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/NBafr100.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/NBafr100.inc
- C:/Program Files/MegaSquirt/mtCommon/NBafr100.inc
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/NBafr100.inc
NBafr100.inc:Close
r kpafactor4250.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/kpafactor4250.inc
- C:/Program Files/MegaSquirt/MS1 Extra 029v/kpafactor4250.inc
- C:/Program Files/MegaSquirt/mtCommon/kpafactor4250.inc
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/kpafactor4250.inc
kpafactor4250.inc:Close
r throttlefactor.inc
+ C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/throttlefactor.inc
throttlefactor.inc:Close
r units.xml
- C:/Program Files/MegaSquirt/MS1 Extra 029v/mtCfg/units.xml
- C:/Program Files/MegaSquirt/MS1 Extra 029v/units.xml
- C:/Program Files/MegaSquirt/mtCommon/units.xml
+ C:/Program Files/MegaSquirt/MegaTune2.25/mtCfg/units.xml
C:\Megasquirt\Software Pack for MS1 V3 SnE 029v MLV 2.95 + TS2.94\3928 & V8 Std CAM and zero trim.msq:Open
WARNING(04): Constant "egoTemp1" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "fastIdleT1" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "egoTemp2" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "fastIdleT2" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IdleAdvCLT" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IATBoost" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IATBoostSt" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IgAdvDeg" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IgAdvTemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IgRetDeg" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IgRetTemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "NosClt" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "OvrRunClt" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "WaterIIat" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "efanofftemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "efanontemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "ASEFixTemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "IATCTemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "fastIdleTemp" units mismatch, "F" in msq, expected "C" from ini.
WARNING(04): Constant "slowIdleTemp" units mismatch, "F" in msq, expected "C" from ini.
Warning Details
---------------
WARNING(04) means that you have different units set in the msq and
your current configuration. This almost always means
that the value of the constant is incorrect and you must
manually correct the situation. The easiest way might
be to reset your configuration's settings, say from
Celsius to Fahrenheit, then re-reading the msq.
C:\Megasquirt\Software Pack for MS1 V3 SnE 029v MLV 2.95 + TS2.94\3928 & V8 Std CAM and zero trim.msq:Close -
Ok, the msq file that I'm using in both the ecu's is the only variable I could be effecting and I haven't changed any of the system files.
The tune in the old ecu is the same exact code that I loaded into the new ecu.
Does this then mean that it's probably a component failure within the ecu?
-
FF
Basically yes, or at least for now it appaears so.
Stopping and reloading before originally fixed it for a while but the last time I reloaded it only partly restored power but it got me home - 60 miles
As the fault only appears after a few hours of driving it'll take me a few weekends to test as you ask as I don't have much time due to available daylight and work commitments.
Where I've mounted the ecu, behind the cubby box, its a bit of a faff swapping the ecu's so I'm going to have to mod the install as well which'll take a while.
I'm not familiar with the way the software works, are the setting files different from the tune files? I have the same tune loaded in both ecu's now.
-
I have two fuel tanks fitted in series both of which are vented. I get no swoosh when I open the filler cap and had no problems before.
The fuel pump is only two years old and an original lr part. I have an upgraded regulator with gauge set at about 42psi from memory. I can set up my drift camcorder to read the gauge to see what's happening as I drive.
I can't discount the above but as reloading the tune made a dramatic difference these are less likely I would have thought.
The edis, would this failing effect the duty cycle?
I went for a short drive last night with Nigel's spare ecu and its running ok. This weekend I'll put 60 miles on it as it was then it was really noticeable before.
Thanks for the replies, I think it's almost cracked now.
-
Hi, back again. Was off-line due to a family issue but now that normality is returning keen to get the motor sorted, thanks again for all the help and advice.
Ok where am I now, well, Nigel kindly sent me his spare ecu that I just connected up.
Went out for a little drive and logged the results (attached)NIGEL ECU RUN 1.xls
The only thing I'd had changed was the authority to 5% and the idle down to 1000 from 1400.
It was only a shortish run but performance didn't feel like it was degrading, I'll need to run it for a few more hours to make sure though.
The log is below, the gego looks a bit on/off - is that ok?
I ran the analyser which changed a few figures which I saved but over wrote the idle rev range keeping them original. Again, is this ok - how you do it?
I still need to set my base idle and double check my timing (never seem to have enough time) but it appears to be running ok this first time out.
Fingers crossed.
Kev
-
the logs are too big to post 4mb, can I email them?
where do I find the settings file?
-
I went out today greenlaning and logged most of the day.
Here is what happened.
I'm using Nigel's tune and have only modified the idle and the controller authority from 15% to 5%.
Spent the first 6 hours running fine then I noticed a drop in power which came on gradually. I reloaded the tune with controller authority set 0 and although there was a slight improvement. Completely shut everything done and reloaded the tune and switched off completely and waited ten minutes. It then ran better but still underpowered slightly and degraded further as I drove home which was a fifty mile drive.
Looking at the logs it looks ok until the problem really is noticeable and the volts, on the log, then starts jumping about.
It's like a component starts to breakdown. Reloading the tune helps but doesnt cure it, it starts to degrade again.
In answer to fridgefreezers questions, answers below'
Are you using Nige's supplied firmware & settings? basically yes
Have you changed any settings?yes, idle speed and the authority
Can you post up your settings file? I'll try
Does stopping & restarting without touching any settings make a difference?no
Does popping the fuel cap off change anything?no
I'll load up the logs shortly
thanks in advance
Does disabling the EGO correction (0% authority) change it?no
-
Tank vacuum. A possibility but never had that before and it wouldn't explain why the volts would drop. Also when I filled up with fuel the vacuum would have been released, no whoosh, and I wouldn't have only noticed the change in running once I loaded the tune at idle.
Thanks again for all your input.
Just to make sure, when I load mt, it's the first ms version in the list I choose?
-
I will post a log when I next go out, although the voltage drops the same as my first post from what I saw. (I've got an issue to deal with first b4 i can post, will sms Nigel to explain)
Spark plugs are new and gapped as per your recommendation.
The map performance issue doesn't reset based on a rest, it's seems cumulative in terms of misfire as you go one regardless of stops and starts.
It was awful as I stopped for fuel, filled up, and then reloaded the map. You felt the hiccup and then it noticeable ran better at idle and off it was back in hooligan mode.
You remember when I used TS it went crazy first time out it went crazy, would this be connected?
-
step size = 1%
authority = 15%
-
No, I didn't have the laptop connected.
-
just the afr was off and it smelt really rich which would explain the misfire. If it was a sensor would it just go bad and stay like that, but this actually gets worse as time goes by, as if its getting more and more corrupt.
-
Bad news I'm afraid, the problem is still there.
After about 30 miles you can feel performance degrade and it starts to misfire again, getting worse and worse.
Reload the tune and its back running well again.
-
Thank you. Little steps for me and lots more questions to come I'm sure (sorry in advance)
I can't believe the wheels spin away from junctions now, next i'll be moaning about broken cv joints ;-)
-
Lets see if I've got this right.
Disconnect the PWM plug and clamp the hose between it and the back of the plenum.
Then adjust the idle screw on top of the butterfly valve with a warmed up engine.
Will that work or do you really have to undo all the pipes and block? (mine are uber tight)
-
A quick update.
The misfire got worse, anything over 1500 revs it was hopeless and barely went over 30mph
I swapped the coil packs, no difference. Checked the wiring, all seemed ok and re-routed the 12v alternator output so it wasn't near anything ms related.
No change. Quite dejected at this point.
Then I re-burnt the tune I had saved and voila, all fixed. It revs out and pulls well. It should have been exactly the same but this time it runs a treat.
The engine starts well but I now need to tune the idle which is a bit high and slightly lumpy.
So all good, well alsmost, the inlet manifold gasket is leaking. We changed it when we were installing MS so its a bit disppaointing I've got tear it apart again. If it aint one thing its another, thats land rovers for you I guess.
-
What drives the duty cycle, what is it a function of? Is it from the map itself or does MS work it out on the fly?
On your setups do the volts drop at all when you open the throttle? What type of things could cause the MS board to drop voltage based on hitting a particular rpm?
I haven't tried different coil packs yes (as my mates got my truck this weekend for some welding) but is this still a possibility?
IAT heat soak
in MS-Megasquirt/Jolt
Posted
It's mounted to an ally plate, along with the ecu and relays, that is bolted to the back of my cubby box.