V8RRC
-
Posts
120 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by V8RRC
-
-
Thats a very tidy job you done there I like it
-
Loads of fun but I spent an obscene amount of time making it.
Nothings changed then Will
-
Top job there Nige
very tidy!When's it out for it's official test?
-
-
Mine turned up in todays post
Cheers Les....
-
Graham, Both of Andy's Discos run just below half as well so I would say the stat is likely to be the problem
-
Cheers Luke thats the same as the one I took off the other day with the over voltage problem!
Will get a new regulator/brush pack & swap it when I get the chance
-
Thanks very much for your input guys!
I will get another & give it a go!
-
Cheers Ralph
I did not think it was right but thought I would ask & get a second opinion!
-
Evening all,
Just a quick question regarding the output voltage of my alternator!
I changed my alternator about 2 months ago & all seemed ok, I have a digital voltmeter fitted & it has always sat around 13.9 to 14.1 volts when the engine is running until Wednesday it deceided to change & it now sits at either 15 or 15.1 volts & only dips slightly when loaded! (lights on ect) Today to eliminate a fault on the volt meter I tested it with my multimeter & it gives the same reading!
So the question is, is my replacement alternator throwing a wobbly & is likely to pack in or is a 15 volt output ok?
Cheers,
-
I know the wires you mean, they are also on my RRC & they arn't connected to anything (I don't know what they do either) so I just made sure that they could not short out & secured them to the loom!
-
Hmmm...If it was mine I would got for number 1
-
"OK I've got the power switch in shot now..."
Ahh..There she is
-
Maybe it's that big Nige is currently stitching the photos together with photoshop or trying to locate a wide angle lens...
-
Hmmmm....Thats a tidy job you have done there
Since I am planning on fitting extended hoses to my RRC now I have seen it done I am also tempted to swap my 2 pipe setup to a 1 pipe system
-
I brought a 300mm one for the rangey & it was far too small
But I am looking for one around the 350mm size myself as that would seem to be ok!
-
Jim,
You could have a look here & see if they can sort you out!
I have used them in the past & found them very good!
http://simplybearings.co.uk/shop/index.php
Regards,
-
My RR also has movement there as well! I was concerned about it until I checked the 2 disco's at work & they are both the same!
-
Maybe it's a DIY scrapiron x-brake
It has orange paint on it -
i have to ask, what on earth (or indeed not) do you build out of 90mm steel?
blast doors?
I think Nige might be thinking of a mk 4 rear winch mount
Coat,Hat,Door..........
-
Sorry i've been so long in replying.
My lightbar came from Greenlane 4x4 too, so we're obviously all chaps with splendid taste!
No probs dunc
Next payday Greenlane will be getting a call!
Cheers,
-
Greenlane 4x4 is where I got mine from....I think!
Cheers for that
I have had a look on Greenlane 4x4 & yes they have them!
-
Nice one
Where did you get the lighting bar from Dunc as it seems far better made than the one I have been looking at?
-
V8RRC
thats just the think i want to do, cheers for the pic
Russ
No problem Russ
It's quite handy that you can remove them pretty quick if the need arises & they seem quite happy offroad!
very tidy!
Time to look CHILLED
in International Forum
Posted
Jim, Put me down for 2 x Large please! Can do Paypal...