Johannadine

Can someone Please help me with the wiring for the Ignition coil and the Petrol pump.

i also replaced that

could it be doing this because the Oxygen sensors are out? soooo stressed

I replaced the TPS but what is the CTS

The Garage is asking me a arm and a leg everything here is so expensive they want to charge me R25 000. we did the full diagnostic manual test and everything seems to be fine thats why we giving up and doing the carbarators the Dizzy Cap, and Rotaor arm - they are geniue parts has anyone checked the timing (is fine has been checked), and also what are the plugs (we changed the plugs) What state is the air filter in,(a new air filter) whats the pressure in the fuel rail (Pressure fine) It is a standard 4X4 Just after we bought it, it started with the problems so then we sew they took the oxygen sensors out and they fiddled with the Air flow meter. Then when we stop by a stop street it reves high 2500 rpm for 5 min. then it only comes down. The stepper motor closes but not fully. when i put it off it has a flat spot and back fires through the air cleaner. and when it stalls in gear it floods and wont start after 20 min.

Its leaking oil.

we have been through the diagnostics test and every thing seems to fine. we did change the throttle position sensor, changed the ignition coil, change the coolant temperature sensor. But when we bought the land rover we sew they had taken out the oxygen sensor and they fiddled with the air flow meter. And here by us these things are very very expensive and you can only get it by land rover agents here by us.

My land rover 3.9 V8 when i want to pull away from a stop street its like it has a flat spot and the engine wants to stall. and it does not have any power tell i push the petrol flat down.

yes went through everything. cant seem to find the problem.

im so tied of trying to find the problem im ready to convert. they want to charge me R5000 for a gasket set what are they going to charge me for the rest.

We are battling with the fuel injection too much. and here in south Africa they asking us so much for spears.

I want to change my 3.9 V8 EFI to carburetor. What wires do i need to change and do i have to put another petrol pump in. Thanks

Ok. what we do see is that the land rover used to be a automatic and they went and changed it to a manual. could it be the road speed input sensor. And where is the road speed input sensor located. thanks

yes i have to 600 rpm. but then as soon as i connect the stepper motor again it rises to 1000 rpm and when i drive and i stop by a stop street it goes up to 2500 rpm and after 5 min it drops to 1000 rpm again.

OK i checked there are no air leaks and when i put the land rover off the stepper motor is pulling back. and when i put it on it is pulsing. but it is still revs high when i stop at a stop street. I AM STARTING TO GIVE UP

Ok i did check they are all closed. i have checked everything the only thing i have left to check is THE plenum chamber will check if there is any leaks there.

When we bought the land rover. we sew they took the cruise control out.

Where is the plunger. and where could the vacuum leak be could it be my fuel pressure regulator vacuum pipe. Sorry very very stupid at this we still learning. Thanks

The stepper motor is clean

I would like to find out why does my stepper motor when i drive and then i stop does it take 5 min before it closers and then only does my ideling drop.

Thank you for your advice. i will check and get back to you thank you so much

Hi i have checked the timing.

hi they changed the throttle position sensors plug and i dont know if they put the wires in correctly . Cause when i take out the sensors plug and turn it with my hand when the engine is idleing the engine stops. Where can i get the diagnostics guide

My land rover 3.9 V8 when i want to pull away from a stop street its like it has a flat spot and the engine wants to stall. and it does not have any power tell i push the petrol flat down.

What does the Throttle position sensor do. And how can i see if it is faulty