Hendrik

Have a look at the masterpull XD ( http://www.masterpull.com/results.cfm?catid=1760 ) it is a rope with a sleeve. A lot of competition trucks in belgium use them ( from http://www.dgtuning.com ) and are very pleased by them. It doesn't feel like a rope but more like a wire cable because of the hard sleeve.

I run full hydraulic steering with the normal pas pump, but I would like to a bit more "oil-flow" (is this correct english). To get this I would like to install a smaller pully on the pump, but are they available "off the shelf"? Thx Hendrik

Thanks guys, Seems to be the same problem as I have... will look tomorrow at my type of calipers and try to contact Rally design for a Brake MC! keep you posted! H.

Indeed tom, That's what I'm looking for... I installed wilwood brakes but after getting all the air out of the circuit, it's still not braking well (like a sponge...). Now we think that the "volume" that the cilinder pumps is not big enough for the wilwoods...

It's about the master cylinder (wasn't sure about the name) part number NRC9529 for a 90 and NRC8690 for a 110/130. Thx H.

Hi, Can someone tell me how much flow the standard defender brakepump provides? thx Hendrik

Looking great! Pics of the steeringbox would be nice if you have them... Thanks in advance! Hendrik

I'm trying to "add" hydro assist on a standard steering box I tought Paul Wightman did this conversion on "Pig"? I'm looking for pictures on where to drill the holes.... Anyone? Thanks! Hendrik

I found a twin plenum from a rover SD1, but I don't know anything about them. what do they do, what's the improvement for the engine (bhp / torque) what do you need to change? And of course what are they worth? H.

Fridge, BBC and HFH I just sent you the logfile via mail, hope you can discover the cause for the misfires... Going to start reading now about "tuning"! Thanks again all of you for your great help! H.

Connected the new sensors today a MUCH better result! Although we still have some misfires (have to start reading on how to solve them). Did a bit of testdriving today and now have a logfile of 12 minutes so for those wo are interested.... BTW: a small movie about the first test: rgds H.

lots of info on here: http://www.megamanual.com/ms2/EDIS.htm

They were, but had no Idea which ones we used . To avoid problems I ordered the new ones on monday...

Sensors are in! Will test them tomorrow! What do you want me to check on the wiring fridge? Thx H.

As I have no idea which sensors I use, I have just ordered these: http://www.extraefi.co.uk/products.htm#tempsensor. They normally should make life a bit easier I think (hope). Normally I should have them in tomorrow or the day after so we can start testing again! Starts to become fun! H.

So because CLT and MAT are not OK it runs rich? why? If I sort these out, it should run better... Will the msq solve all the probs? or something else I can do? Thx!

yep now sent! rgds Hendrik

Hi Nige, I'll mail the XLS file to you, Ian and John, so you guys can have a look at it. Unfortunatly I'll be only at the car the soonest on thursday/friday. Thanks in advance! Hendrik

For example can you post up The version of the MS ECU system you are using: V3 PCB running MegaSquirt'n'Spark-Extra firmware EDIS 8 or not: yep Trigger wheel, how mounted and where is the "Gap" in relation to the VR Sensor: Trigger-wheel.com wheel, will take a pic of it asap What Version of software have you got in the MS and is the ECU "Talking" to the Laptop ? MSNS_Extra - James Murray etc. connection to laptop OK now...! What sensors your using (CLS MAT): I'll have to check... Which coil packs and how wired (I have one wrong on my MS Start up and it was horrendous : Coilpacks are OEM Motorcraft with Magnecor 85mm leads with High temp connectors What fuel pump your using: Fuel pump is Bosch High pressure (will post the partnr asap) How have you done the wiring ? - new loom as with me or modified existing one in which case just run through what went to where: The wiring is indeed a completely new loom made for the car. Have you powered the MS from a live wire and not from a wire live when only cranking ?: I'll have to check it out... VR sensor, can be wired the wrong way around: we'll try to switch them around! The above would then give those who know a fighting chance of sorting I have tried to datalog, which gave me an excel file, if you guys want it I can sent it via email (as I'm unable to upload an xls file.) thx Hendrik

OK guys! I'll try to answer your Q's asap! regards Hendrik. P.S. we keep on smiling!!

plan can work the other way as well, we can come to the UK with the truck on a trailer too... Maybe next weekend or within 2 weeks? I really want to learn the program / system! looking forward to your reactions! thx H.

@Ian: you have mail

Hi Ian, can I give you a call? working on it at the moment and when I unzipped the file and want to open it i get the message: The zipfile has not been extracted correctly - please ensure you 'use folder names' or create sub directories when extracting. This batch file cannot run without: src\CHOICE.COM src\DOWNLOAD.EXE msns-extra.s19 . Aborting Press any key to continue . . . If anyone can help me with this, I would be very happy (I feel so stupid...) thx H.

you guys are great!! OK, when I open megatune I get this "pop-up": http://pix3.telenet.be/S5nYkAdoSbhvllW7Aai.../megasquirt.jpg on this one I first took MS 2 Extra 1.0.2, but I now have created a new project (V8 project) with below details: http://pix2.telenet.be/S5greM4ICS8EeISNdAS...onfiguartor.jpg is this correct?