defender dinky

hi, yes it was genuine part, had part number off forum. cheers

hi all, getting rather fed up now,oil leak at first thought it was sump gasket by bellhousing, removed sump cleaned everything up,let oil drain out of engine over night without the sump tray being on, oil seeping down face of bellhousing not from drain plug hole thou, as changed rear crank oil seal earlier,cleaned oil off bellhousing again left for an hour or so, oil back again, the landy is facing down hill at this point so i would have thought the front of engine would be the lowest point, put new gasket back on and is still leaking, wondering is there a seal between engine block and belhousing that could be leaking,used torque 18nm on sump studs, any help on this would be gratfully received thanks wayne

hi,thanks, now i can put seats back. wayne

hi all, having trouble with difflock gear stick , but sorted now, while investigating i foung what looks like a filler plug in the housing on the back of it by two wires, removed plug and it was bone dry inside, should this be lubricated at all, oil or grease, put my finger in felt some thing and when pressed main gear lever moved. cheer's wayne

hi steve, got in it this mornig every thing seems ok? for some reason, just found what looks like a filler plug back of difflock gear stick taken it out and it's bone dry do i put oil in it and what type cheer's wayne

hi all changed tranfer case rear oil seal put all back together now have no drive only if i put it in difflock, can anyone help cheer's wayne

hi les,oil seal done, 30mm nylon nut was just about hand tight but changed it anyway, now another problem got no drive unless in difflock is it because i forgot to jack up wheel, i got a pit and didn't think i needed to, any solution on this cheer's wayne

just under defender now and all nuts loose on universal flange could this be why its leaking thanks defender dinky

hi, les my gearbox is lt77 comparing it with gearboxes ive seen on achives would this part number still fit , cheer's wayne

hi les, thanks for that. have you part number cheer's wayne

hi all,under defender this morning found oil leaking from back of t/box from uj's, please tell me it's only a oil seal, and possible solution. thanks defender dinky

Hi, I have a defender 90 and was wondering where i fill the transfer gearbox up with oil? Is it through the breather pipe? All Help greatly appreciated. Thanks, Wayne

hi paul,thanks for info, what's clutch fork, and how much am i looking at to replace these items, any idea why my high & low won't change cheers wayne

hi,all, changing crank seal tomorrow, is there anything else i could be checking while down there,i'm splitting tbox from gearbox already to come out, for some reason i can't get high or low range, looked at it tonight but got to dark can't drive it at the moment no sump on either cheer's wayne

morning all, just inquired about rear crank oil seal part no err1535, and was told does'nt mean anything, quoted me £30 for a copy is this going to be any good to me. cheers wayne

hi, does the oil inside mean my rear crank oil seal has gone. cheer's

Hi, Just finished working on defender and found a hole in the bottom of the bellhousing. It looks as if there is a stud missing right at the bottom. The hole was full up with grease oil of some sort. When i scraped it out, Guess What, it was full of engine oil! Should this hole have a drain plug in? I Have a picture to show you what i mean Cheers, Wayne

hi that's what i'm dreading although seen very good archive on this site, what is part number for rear crank seal, how do i go about leaving donations to this site,and how much, wekly monthly all at once cheer' wayne

hi neil,i took sump tray off because it looked like gasket had gone put new one on topped up with oil , had a look a bit later on and oil seeping from back end of sump tray, took it off again cleaned everything up let it dry for abit another new gasket just incase , and before i put it back on i could see oil seeping from between back of engine & bell housing, there wasn't any oil in then, torque set as 18nm is that right , is there anyway i can check rear crank seal without taking gearbox out , i will check back of engine off work thurs & friday, i'm in build trade not very good at the moment, cheer's wayne

hi neil, do you mean drain plug bottom of gear box, if so no oil leaking from there, cheer's

hi, again fitted sump new gasket on 2.5 n/a, still leaked took it off clean everything up and found oil ceeping from between back of engine and alloy casing, is this possible, if so is it a big job, thanks wayne

hi,my sump his the same as the one's in pictures, already to put back together do i use gasket or can i use sealant,200 tdi as three longer bolts at front of sump according to haynes manual my bolts are all same size. thanks for all your help wayne

hi matt, have removed sump by removing part of the exhaust, no breather pipe on drivers side, am now removing parts of cardboard gasket not silicon can i put silicon back instead of cardboard? cheers wayne

hi,orange sump nearly off but looking inside best i can, looks like another tray inside sump cover and theres something big and bulky stopping it from dropping down this sump as a gasket on does this mean anything , i was told when i bought it , it was a 200td pre 95 but when i phoned carspares they said pre 95's don't have gaskets on , so what have i got cheer's wayne

sorry, it's diesel 200 td