Tetsu0san
-
Posts
757 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Events
Gallery
Blogs
Posts posted by Tetsu0san
-
-
My two pennies worth is rotate the original pin as far as you can and that'll do it. The EGT gauge is useful I guess but I think it's only really important if you push the engine hard all the time. Normal driving with a bit of a push every now and then doesn't really need a constant exhaust temperature monitoring system.
I rotated my 300Tdi pin to the max about 18 months ago and never had a problem. Equally my 200Tdi has had the same done as well as a few other tweaks and this has been like it for 5+ years with no ill effects. Neither have an EGT gauge.
You can easily get bogged down with monitoring this and that but ultimately unless you're running full bore all the time I don't see the point.
-
7 minutes ago, Sheffield said:
I am not sure about the "one shot" grease, if you want to keep the vehicle for a long time. Not only is it not as good a lubricant as oil, but if the seal not sealing fully and would let oil out it will let water in. With oil you can check the level, and change the oil from time to time, flushing out any water. But how do you check the grease, for condition or quantity withiout dismantling the hub?
Land Rover had good reasons for introducing the grease, but if you are prepared to look after your vehicle I suggest you stay with EP90 oil.
There are two schools of thought regarding oil/grease and both have their pros and cons, however implying that grease is no good if you want to keep the vehicle for a long time is a bit misleading I'd say. I'm sure some will say that you have to have oil because of the reasons you stated above (which I agree with) but also the state of the swivels, the quality of the seal, the usage of the vehicle etc will all dictate as to how well the seal will seal, and oil has a greater possibily of leaking out than grease if any of these are sub par.
Personally never had an issue with grease and I'd use it every time. Horses for courses I guess. -
Ah, you mean the swivel ball seal? The big one?
I've not seen a metal backed on before so I guess that's what you get on a model I've not pulled apart. All the seals I've seen have been rubber and just slot in being held in place by a metal retainer. I've seen 2 metal retainers being used at the same time on an old 90 I used to have but when I didn the seals I just removed the additional retainer and only used one. Seemed alright and didn't leak.
If the new seal fits and sits flush to the outside of the housing so the metal retainer can do it's job then I can't see an issue. To reduce the risk of leakage use the one-shot grease rather than oil in the hub.
-
Which seal are you talking about? Got a picture?
-
Yes, I'm positive they're the same.
-
Apparently they are interchangable after all so I'll be giving that a go. I'll report back if it's not the case.
-
1 hour ago, vulcan bomber said:
300 swivels will have top and bottom bearings.
Yes, but the 300Tdi ABS models have a different set up on the top for the sensor. I wanted to know if these swivels are interchangeable with the railko type swivels on my '84 110.
-
Morning all
I've got an early 110 which has (or at least should have) the railko bush type swivels, and they're pretty rough and could do with being replaced. Is a swivel from a later ABS model (such as a Discovery/Defender) the same? I don't want to replace the swivels with the top and bottom bearing types like the later non-ABS models have, and I could source an early chrome swivel that would fit, but I have two pretty good ABS swivels from my old Discovery that I would like to use instead if possible.
Cheers
-
9 minutes ago, Stellaghost said:
I have also picked up a 200tdi Discovery although it's a 5 door interior is very hard up but chassis sound and body retrievable in my opinion just dont know whether to restore or break it just got so much on at the moment regards Stephen
When I got the two door I also got a five door 200Tdi and a MK1 Hilux from the same seller. All this along with a VW Beetle, my existing Discovery, a Defender 90, and my 110, I've got more than enough to be getting on with.
-
1 minute ago, jason110 said:
Thanks for that. Think I’ll strip it then and list the bits and hope they shift. So you think the bigs bits like engine, gearbox, transfer box, axles, steering pump are worth saving? I’m asking because ive been out of the game for a while and I’m aware it’s a 20 year old plus truck so demand for certain bits might of changed.
Oh, don't get me wrong, I'm not in the garage game. I'm just an ejit who for some reason likes getting oily and dirty underneath a Land Rover.
The way I see it is that if you've got the space, take the bits that are most likely to be needed by either you or someone else and scrap the rest. There are more people out there like me who would be interested in an engine, a good gearbox, a transfer box as an upgrade to an old 90/110, rear axle convertion (like I said earlier) but don't really want the hassle of buying the whole vehicle themselves, removing the parts twice (once from their vehicle and again from the donor), and then getting a dismantler to collect what's left.
Discovery 1's are getting rare on the road, but small parts are easy to come by. However good big bits like engines etc are always desirable to the right person. However, this is the opinion of an ejit.
-
4 minutes ago, Stellaghost said:
Explain this further please regards Stephen
There's just something about two door (or three door if you count the rear door) models that seem to attract people. They're rarer than the five door version and even though they're probably more impractical they seem to be more likely to be bought and restored rather than broken up and scrapped. I would imagine that in a few years time (if not already) they will start to demand higher money than the five door models. You certainly don't seem to see as many two door interior parts at jumbles compared to the endless seas of five door stuff.
As a side note I recently picked up a two door 200Tdi Discovery and I fully intend on getting this up to scratch and replacing my five door 300Tdi with it.-
1
-
-
If it's not likely to go on the road again due to being a potentialy massive MOT failure then you kinda have to go from scrap value and work up from there. If you're capable of removing the engine then that's going to be worth a couple of hundred at least and then the carcass about £150ish weighed in.
Value of a vehicle is, as you say, dependant on what people will spend but equally if you break the vehicle then all the good parts have value. It just depends on how far you're willing to go. Rear axles for people who have old drum brakes 90's are worth a bit, front axles too if the swivels are good, power steering boxes are usually in demand, the list could go on.
But if it's unlikely to go back on the road easily and you don't want the hassle of a major stripdown then I'd take out the engine and gearboxes, remove the axles, take a few other choice bits and store them, and scrap the rest.Unless it's a two door....
-
5 hours ago, monkie said:
This could be a slippery slope to a full rebuild. I assume that the engine has been fully serviced, valve clearances checked and adjusted as required, timing has been checked and the hoses from the turbo, intercooler and manifold are in good condition?
Totally agree here. Where do you stop? If you change the big end bearings, rings etc then you might as well rebuild the whole thing. For me, if it's not losing oil and water then just do the clearances and any seals that are leaking. At a push re-seat the valves by removing the head but only if it's obvious that they're leaking.
If it's a bit down on power then maybe rotate the boost diaphragm and give it a good service? -
It sounds like the injection pump to me as I'm having the exact same issue on my 300Tdi Discovery. I've been running my Discovery on normal diesel and I decided to try some veg oil (as I run 25/75 in my 200Tdi 110 anyway) and ever since then I've had a fuel starvation issue.
I've replaced the fuel filter, cleaned the gauze filter in the lift pump (it's a Delphi one), blew the fuel lines out too but I suspect my issue is in the tank or sediment filter.
But for you to be sure try and get an engineers stethoscope (or a long screw driver) and see if the sound is coming from the injection pump. I suspect it is.
-
2 hours ago, ThreeSheds said:
Well it was orange and I thought that meant OAT... But no - I am not sure since I didn't put it in...
Anyway - ALWAYS tastes foul you say? How often do you resort to drinking it then
Unlike you it's my first time - but I expected that the french wine additive part of it would be sweet? Perhaps the brand that was in the D2 was chaep (no bittering agent)...
The old alcohol based stuff was always sweet, and tasted great until you go blind. The OATS stuff just had a very bitter taste. However, if they do add a bitterness to OATS then I've just been unlucky and need to find a better brand. Moonshine doesn't make itself...
-
1
-
-
That stuff always tastes foul to me, are you sure it was OATS? Either way, make sure your health insurance is up to date, and you've made a will.
-
14 hours ago, western said: cool, can we see a photo of the complete truck please.
as to loom route. on my 200tdi the loom comes from bulkhead connectors along the right side of engine at cylinder head to block joint, wires to alternator go between head & thermostat housing then down to alternator, plain brown wires to starter go around the rear of engine then to starter soleniod & meets the main power cable from battery bay. [ loom took the same route on the original TD engine, it's the same loom]
Cheers for that, but I was more wanting images from a 300Tdi.
-
22 hours ago, western said:
Leyland Octopus or Albion variant not sure if Maudsley made a 8 legger.
Boom, it's an Albion!
Anyway, moving back to my original question does anyone have any pictures of the routes that the cables and pipework take around the engine?
-
2
-
-
Just now, western said:
Atkinson ?
Nope. You've just said one that you didn't say earlier. One of your previous choices was right...
-
32 minutes ago, cackshifter said:
Saurer? Just kidding. I think its a Guy.
Nope, sorry. Not a Guy.
-
1 hour ago, western said:
Leyland octopus
Albion
Guy
Maudsley
Throw as many names at it and hope something sticks? Pick one....
-
38 minutes ago, landroversforever said:
Not familiar with the model names, but something ERF or Foden? 🤔
Nope, afraid not. Keep going!
-
8 hours ago, landroversforever said:
Instinct says Scammell. Maybe a Routeman?
Nope, sorry. Not a Scammell.
29 minutes ago, Arjan said:Big Lorry ?
Looking a good project.
...and love the workshop
Yes, it's a big lorry. 8 wheeler no less.
Project is coming on, and the workshop helps, that's for sure.
-
22 hours ago, landroversforever said:
OT but what’s the vehicle in the background?
Ooohh, I could give out a prize here for the correct answer. The Beetle is a 1303s that I'm in the (very slow) process of getting running and road worthy for my daughters 17th, although I'd prefer her to have this 90. Now, the lorry is something a little rarer. Any ideas? It's from the 50's...
-
1
-
Newbury autojumble postponed
in International Forum
Posted
Well that's put a stop to pretty much all I had to look forward to.
Balls.