-
Posts
28 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by hundertneuner
-
Hi, currently i'm converting a 109 series 3 to V8 using an LT 85 a part-time LT230 and the original mounts as used in a 110. Yesterday i've started to put the drive train into my chassis- is it right that both propshafts can not be set parallel to the fictive middle chassis line? So in a 110 (V8) with salisbyury diff the propshaft setup is angular? Best regards Sascha
-
Hi! Is the "classic" 4 spoke steering wheel of 90/110 (also found in RRCs with different wiriting on the "impact-cussion") the 19mm type??? I've recently bought a new steering column (the seller beliebved it was for a 200/300 Tdi, but he wasn't certain) for my power steering conversion. I' just tried- the original TD5 steering wheel doesen't match this column... how many different of types of 90/110/Defender columns do exist??? Ciao, Sascha
-
I am running 33mm wheelspacers in combination with (standard) 5,5x16 wheels and 7,5 inch tyres. I´ve done 10.000 km since fitting them and had no problems- the turning cycle is now really nice and driving through curves even better. See pics below. The spacers were for free, so hadn´t to go for other wheels and tyres; the combination of wolf wheels and 235/85x16 would be my prefered option.
-
yes, i am going to transplant it into my 109 next spring. it is not the first box, but i want to substitute the pricy german traders for parts...
-
I have to rebuilt a worn LT 85 gearbox. Where should i buy the needed parts? LEGS or Ashcroft or???????
-
...what about this engine setup: http://uk.youtube.com/watch?v=9zjSnGgrXQU
-
you´re right- and i was: sascha
-
how do you know this? the fact that his landy is a series 2 isn´t a good hint for the engine-type (3 v 5 main-bearing)that is currently installed... it was maybe updated/changed in the past (or is the kind of flywheelhousing pictured above a hint???)...
-
you only have to remove the last bearing-block of the crankshaft, located next to flywheelhousing. don´t you have a workshop-handbook for series vehicles? it is available in the internet without problems and without having to pay for it... i´ll send you a pm with a link for that...
-
the crankshaft-seal of engines which have got 3 or 5 main-bearings are different. the older 3 main-bearing crankshaft has got a "slip-over" seal (there is a cut through the oilseal) and the 5 main-bearing crankshaft is a "push-on" seal 8 (no cut), like in all later ( i think past 1980) engines... make a pic of the side of your engine, so we may identify a 3 or 5-main bearing engine!
-
SIII 109" Salisbury disc brake conversion?
hundertneuner replied to XtremeMarineInc's topic in Series Forum
Maybe u give Paul at www.heystee-automotive.com a ring/try? Very friendly guy, i´ve seen this kit sometime ago: really good craftmannship and common parts used... i will go for such a kit (front) next year: perhaps this kit matches the sal!? ask him.. -
Hi Andy! May u shoot some more pics of your nice truck, especially the corners around the axles??? C heers, Sascha
-
really great! i am very impressed about the mods you guys do over there! please keep us updated, especially the upcoming 101/ENV axle conversion... cheers sascha
-
..wow- a great toy you own there! Please keep us updated with your projects on it!
-
Series 3 lower dashboard refurbishment
hundertneuner replied to hundertneuner's topic in Series Forum
Thanks, David- I´ve just been on your homepage to have a look at your project: Very nice! Sascha -
Hi! My lower dashboard of my exMoD 109 was a little bit tired (after the army rocked it!)- so i decided to refurbish it. It was stripped, sandblasted and painted again. But before it was sandblasted, i welded an wind-guiding-plate (can i say like this??) into this box at the right side (see pic) and made the gap for the footwell at this side smaller. now i have got the same amount of air at both sides of the dash... Then i refitted the cleaned foam-part and glued it on. Tomorrow, with my mum´s help, i will put some new synthetic leather on it! CU, Sascha
-
check this out: http://www.bell-aurens.com/bell-aurens.com/Startseite.html ! it´s a series 2 long v8 creation....
-
-
Hi there! I´ve got a question concerning length oft the steering relay spring of an series3 lwb 4cyl. model. Is it right that the length has to be 184mm when new, like written in the workshop manual? Or is this a misprint??? The length of my old one is nearly 165mm....any ideas???????? Thanks so far....Sascha
-
Great work, minivin! Cheers Sascha
-
...have a look at the hinges- the defenders doors fit without problems to series3 hinges- but yours 2a has different ones as you know, so check this point before, maybe you will hve to change to series3/defender-style hinges or you goota drill a bit... cheers sascha