Les Brock Posted February 29, 2012 Share Posted February 29, 2012 Hi Chaps, Still building slowly....... Can any one knock one of these up for me ?, to allow me to go through the rear tub from the filler. down to the rear TD5 tank in a 90, Ideally with a spigot for the air escape pipe underneath . Nige - You need the practice ....... Foldy notes available I will confirm pipe sizes once I've had a proper measure Thanks for looking Regards Les Quote Link to comment Share on other sites More sharing options...
pitmole Posted February 29, 2012 Share Posted February 29, 2012 Hi, you just need the mount plate with the lobster backed pipe out one side and a straight pipe with small bore branch the other? Quote Link to comment Share on other sites More sharing options...
Les Brock Posted February 29, 2012 Author Share Posted February 29, 2012 thanks for the reply, this might show it better...but then again I'm no artist Filler Pipe I believe is 50mm, the spigot around 10/12mm but I will check the correct bore size tonight at home, just checking the water to see if anyone can make one for me before I have to think of a different way to do it Regards Les Quote Link to comment Share on other sites More sharing options...
stuck Posted February 29, 2012 Share Posted February 29, 2012 Aluminium or Stainless Les? Quote Link to comment Share on other sites More sharing options...
Les Brock Posted March 1, 2012 Author Share Posted March 1, 2012 Either is fine with me Regards Les Quote Link to comment Share on other sites More sharing options...
big len Posted March 1, 2012 Share Posted March 1, 2012 Les, I've just had a look and we have more than enough ali to make one of these from our scraps bin, so I could knock you up one without any material cost. If you could finalise a few of the dimensions I could even weld it up tomorrow after lunch if sooner is better for you The more dimensions you give the better - but mostly how far below the plate it should go , how far above the plate the turn is , what angle the turn is. Oh and the size of the breather pipe. Don't worry I'm not in it for money by the way - I enjoy interesting little fab jobs like this ! Quote Link to comment Share on other sites More sharing options...
Les Brock Posted March 1, 2012 Author Share Posted March 1, 2012 Hi Len, That is superb, I will get some "proper" measurement tonight and post up tomorrow Regards Les Quote Link to comment Share on other sites More sharing options...
Les Brock Posted March 2, 2012 Author Share Posted March 2, 2012 Hi Len, Hopefuly this is ok The filler pipe is 50mm External The breather is 20mm External and really needs to come out at 45 degs to allow decent access without kinging the pipe, or making fitting awkward I've kept the measurements to round figures Ask away if it does make no sence whatsoever Many thanks for this, Let me know what I owe you by PM, and how you'd like it....oh-er ......and where to send it Regards Les Quote Link to comment Share on other sites More sharing options...
big len Posted March 2, 2012 Share Posted March 2, 2012 MASSIVE GRAINY CAMERA PHONE PICTURE ALERT I'll PM you and get it in the post tomorrow - I must run to a stag party now ... ( unfortunately?? ) Quote Link to comment Share on other sites More sharing options...
Les Brock Posted March 2, 2012 Author Share Posted March 2, 2012 Hi Len, That is superb , many many thanks , i'll get your details of your PM Enjoy your party Les Quote Link to comment Share on other sites More sharing options...
DrRob Posted March 2, 2012 Share Posted March 2, 2012 That is a work or art and so generous! What a gent. Quote Link to comment Share on other sites More sharing options...
stuck Posted March 2, 2012 Share Posted March 2, 2012 Respect. That would have taken me a week! Quote Link to comment Share on other sites More sharing options...
ejparrott Posted March 4, 2012 Share Posted March 4, 2012 Top Job! Quote Link to comment Share on other sites More sharing options...
Les Brock Posted March 5, 2012 Author Share Posted March 5, 2012 Len, Sent you a pm Regards Les Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.