defender dinky

Just fitted reversing camera on my van and red wire goes to the connection on reversing light in the light cluster so when you select reverse it powers the camera, dd

When I installed my led lights I also installed a dimmer relay from maplins it acts like a dimmer switch on your house lighting, led lights don't need many watts, dd

Could be relay on the back of fuse board in the cab un screw it off the bulkhead

That will do me then, thks everyone , dd

My left front runs across bulkhead, if I keep the brake box and master cylinder I've got installed, the two ports on the side one to left front caliper one to front right caliper and one underneath to rear brakes, is that right way to do it, I have brake lights, switch is on the pedal, just did'nt know what the switch on the servo was for, would I need to install any more G valves or pdwa's for front brakes, thks dd

Hi, I still have brake lights the switch is on the pedal, dd

Yea mate I'm the idiot, because my other cylinder only had two ports and was unsure what to do so i blanked it, so should I put the other servo on, but it's only got two ports,but has a brake switch, would it work if I just swop the master cylinders over, the photo is of the brake lines on truck, something bolted to chassis can't remember what it's called rear brake line passes through it, dd

Here's the third photo, dd

I'm confused, first photo brake master cylinder has only two ports at the master cylinder but has a switch, second photo is the one on my vehicle, with three ports but no switch, so what would you suggest if I swop brake boxes then I'll only have two ports for the brakes, do I need a switch on the brake box?, third photo showing three ports one is at the front underneath, dd

so the one underneath is rear brake, sorry to be a pain but looked at brake servo and there's no switch like there was on the other one, it came from 300tdi I think, also I now have a switch on the clutch reservoir could you tell me what wires go to this switch, and what do I do about brake servo, dd

Reason I asked is because on my brake master cylinder I have three connections two on the side and one underneath

Hi, great weather at the moment getting loads done on my project, defender 110 91 reg, with 200tdi discovery engine in it, question is, is the clutch pipe work servo ect, independent from braking system, I used to copy things off my 90 but sold it last year, any pictures would be better, dd

Hi, can't see white/green trace on that wiring chart? What model is it for, Dd

Yes, first photo white/green trace, heated rear window, my fog light is on the steering column, in its place is the internal light, thks dd

Hi, defender 110 project, so part have come from various vehicles mainly ebay, think bulkhead was off 300tdi some electrics come with it, question is three switches by your right knee I have internal light, and hazards switch, one nearest steering wheel blanked off but inside is connector block for a switch same as others it has white wire and a white/green trace wire what is this switch for, dd

hi, its my project been going on for a few year now, i lost my unit and its on the front covered up working between weather and other things, couple of photos , dd

hi,found the culprit i hope won't know till i put it all back together, i must have drilled through the loom last year from the engine side🥵 you can just see the plug which is holding something the other side, live and, learn , dd

No lights don't go off, found what looks like an earth wire disconnected looks like it just pushes on to something, it's not a bullet connector or Jack type just atube on the end, dd

Hi, update all switches off, ignition on side lights permanently on, ignition off side lights go off, ignition off turn side lights on by switch lights on dash and can operate wipers, leave sidelght switch on start engine with key, turn key off engine still runs, turn sidelights switch off engine stops, all lights work on truck except indicators, but they do work on the hazards, any ideas, dd

Hi all, my project, defender with a discovery 200tdi engine in it, I had everything working regarding ignition, lights wipers etc., weather picking up a bit so removed covers sheets from truck and do some more work on it, problem i have is start engine with key, no problem, turn key off ignition still on,the only way i can turn ignition off is with the side light switch, took key out and turned ignition on with side light switch any ideas, dd

Yes, all sorted

Ok, if I take rear door card off and all the wires are there I might fit one, thks for your help, dd

Theres not a rear wiper on the car, it was'nt on when I bought it, there looks to be a bung in the hole where it should be, the rear windows work fine, also just remembered the fuel gauge only goes up half way does'nt move until you turn ignition off, no matter how much petrol you put in only goes half way, dd

just tried it again, key in ignition turn to position two all lights on dash about five seconds you here click click, another five or six seconds click click and so on all the time heater ,radio, fans turned off, like i said earlier removed cover under steering wheel had a listen and its louder, removed all fuses and relays all seem ok, and it still clicks with engine running, it sounds like a relay click, dd

ignition on, sounds like a relay clicking, and noticed the suspension not lifting, when turning on ignition, dd