Guest dew110CSW Posted February 25, 2007 Share Posted February 25, 2007 Got an odd problem with the 110, when reversing it Judders slightly, first time it did it we played with the Hi/Lo and the Diff locks and it cured it for a while, backed no problem so we know it's not a tooth off a gear. Did it again today, anyone got any ideas? It's the LT-77 box mated to the 2.5 TD (19J), Standard axles ect... as far as I know with 235/85 A/Ts on. Quote Link to comment Share on other sites More sharing options...
RedLineMike Posted February 25, 2007 Share Posted February 25, 2007 handbrake sticking? stuck in difflock? Quote Link to comment Share on other sites More sharing options...
Guest dew110CSW Posted February 25, 2007 Share Posted February 25, 2007 Surley either of those would make it do similiar in forwards, and playing with the Difflock did sort it for a short while... Quote Link to comment Share on other sites More sharing options...
RedLineMike Posted February 25, 2007 Share Posted February 25, 2007 worked on a motor previously that only did it in reverse cos i the way the shoes were sitting & sticking, also did same kinda thing on my racer when the centre diff exploded thus locking the difflock solid Quote Link to comment Share on other sites More sharing options...
Guest dew110CSW Posted February 25, 2007 Share Posted February 25, 2007 Will have to take a good look then when the weather improves slightly, could be fun... Quote Link to comment Share on other sites More sharing options...
Coastcard Posted February 26, 2007 Share Posted February 26, 2007 Does it judder all the time or just on takeup? Might be worth checking engine/gearbox mounts. Quote Link to comment Share on other sites More sharing options...
Happyoldgit Posted February 26, 2007 Share Posted February 26, 2007 Check the propshaft UJ's as well. Quote Link to comment Share on other sites More sharing options...
widget Posted February 26, 2007 Share Posted February 26, 2007 Mine juddered in reverse when the clutch was on its way out. Low range was horrible. Quote Link to comment Share on other sites More sharing options...
sadoldgit Posted February 27, 2007 Share Posted February 27, 2007 Got an odd problem with the 110, when reversing it Judders slightly, first time it did it we played with the Hi/Lo and the Diff locks and it cured it for a while, backed no problem so we know it's not a tooth off a gear.Did it again today, anyone got any ideas? It's the LT-77 box mated to the 2.5 TD (19J), Standard axles ect... as far as I know with 235/85 A/Ts on. does it judder once your foot is completly off the clutch? if it's just juddering as your bringing the clutch up it's probably got oil on it. poss rear main or gearbox input shaft seal or as coastcard says mountings. is your wading plug in? could have a build up of oil in the flywheel housing. my rear main is pishing oil out and my clutch is juddering in reverse but for some reason not all the time (been like that for 2 years but i keep putting it off!) Quote Link to comment Share on other sites More sharing options...
Andy Posted February 27, 2007 Share Posted February 27, 2007 i had a LT77 that juddered in reverse then it started to judder forwards too. turned out to be the bearing where the 1st motion shaft sits in the end of the mainshaft had died. but you wont want to hear that so feel free to ignore this post. Quote Link to comment Share on other sites More sharing options...
Guest dew110CSW Posted February 28, 2007 Share Posted February 28, 2007 I'll run some of these past my dad tonight (not afraid to say I know buggar all when it comes to stuff like this). Will check all options. The gearbox was a Recon unit around 15 000 Miles ago (done 131k now). Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.