V8SMYMATE Posted August 1, 2008 Share Posted August 1, 2008 Hi i looking for a inner and outer set of sills but are struggling to find where to buy and at the best price any idears will help. Quote Link to comment Share on other sites More sharing options...
FridgeFreezer Posted August 1, 2008 Share Posted August 1, 2008 Box section - then you've got built-in rock sliders Quote Link to comment Share on other sites More sharing options...
CaptainChaos Posted August 2, 2008 Share Posted August 2, 2008 Box section - then you've got built-in rock sliders Just done that to my 200TDI 3 door Not as simple as doing it to a 5 door but still do'able ........ box section measurements were approx 5"x2 1/2" Quote Link to comment Share on other sites More sharing options...
Les Henson Posted August 2, 2008 Share Posted August 2, 2008 Replacing the complete sill on a Disco is major work. The join runs under the seat - halfway across the footwell. It's a lot easier to repair or replace the part necessary. Les. Quote Link to comment Share on other sites More sharing options...
sealt Posted August 2, 2008 Share Posted August 2, 2008 Did this job on my disco1 3 door and found out that it was alot easyer to use a 100x60 box,i used 100x60x6,3 mm since i had 6,3 thickness but makes it even more solid. Had a lot more rust on mine than the pics above,even the inner sill was more or less gone along with most of the floor,so i replaced the inner sill and used box for the outer one Quote Link to comment Share on other sites More sharing options...
gardener_44 Posted August 2, 2008 Share Posted August 2, 2008 I had these made and fitted to my 200 TDI by RDH engineering . Quote Link to comment Share on other sites More sharing options...
CaptainChaos Posted August 3, 2008 Share Posted August 3, 2008 Did this job on my disco1 3 door and found out that it was alot easyer to use a 100x60 box,i used 100x60x6,3 mm since i had 6,3 thickness but makes it even more solid.Had a lot more rust on mine than the pics above,even the inner sill was more or less gone along with most of the floor,so i replaced the inner sill and used box for the outer one Thats almost exactly how i have done mine Great minds n all that Will add some pics later Quote Link to comment Share on other sites More sharing options...
V8SMYMATE Posted August 4, 2008 Author Share Posted August 4, 2008 Thanks for all your help people i will attempt the job next month and report back Duncan Quote Link to comment Share on other sites More sharing options...
disco tony Posted August 7, 2008 Share Posted August 7, 2008 I can also recomend RDH sills. how to fit them Quote Link to comment Share on other sites More sharing options...
lrnewbie Posted August 26, 2008 Share Posted August 26, 2008 Thats almost exactly how i have done mine Great minds n all that Will add some pics later I've just bought my first land rover, discovery 200tdi K reg and I've felt around under the plastic sill covers and uncovered some rusty holes just with my fingers. I need to look properly and I don't know if the outer sill is as important as the inner (which feels ok) but assuming they need to be fixed how much do you think it would cost to get a garage to put in the box sections you've suggested? I don't weld or do bodywork so I have no idea how big a job it would be. Also I assume that you don't have to mess about with car filler and making it look lovely as it is covered by the plastic trim? Thanks. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.