Hybrid_From_Hell Posted September 17, 2014 Share Posted September 17, 2014 Hi All, Need some pics and measurements desperately please for 200 300 TD5 90 or 110 Defender etc. See pics below : The 2 x pics above are from a LHD NAS V8 90 I need for 200 300 TD5 ALL left hand drive 2 x pics like the 2 x above and the measurement from where the Tape measure shows to the 1st bolt in the wing, and then the distance to the 2nd one, again as shown in the pictures ....and then the same on the (For You) Drivers wing, ....dimensions ....and Pics please HELP !!Nige Please can some kind members with LHD Quote Link to comment Share on other sites More sharing options...
greenstream Posted September 17, 2014 Share Posted September 17, 2014 Hi Nige I can get the meassurements from a 300, but cant tell from the picrures exactly where to look. If nobody else can get the 200/TD5 then I can get that as well. Quote Link to comment Share on other sites More sharing options...
henk Posted September 18, 2014 Share Posted September 18, 2014 I can get pictures and dimensions of 200/300/TD5 90's and 300/TD5 110's all LHD I just need to know what you are measuring there ... Quote Link to comment Share on other sites More sharing options...
Hybrid_From_Hell Posted September 20, 2014 Author Share Posted September 20, 2014 ^^^OK On the wing top as you go towards the engine bay the wings have a 90 degree fold down, and there are "Factory" holes in these folds both on the Drivers and Passenger wings. So, as per picture no 1. Place tape measure at the rear most part of the wing against the bulkhead, and also at the point the wing folds down 90 degrees. Extended the tape measure from this pouint, and then advise me of the mm from the bulkhead / Wing point where the centtre point is of either the bolts in the fold of the wings or the centre of the holes themselves and on both Drivers and Passenger wings the 2 x pics above show a Drivers side (LHD) NAS 90 V8 and the hole in pic 2 is approx 413mm from starting point So, I need to know the distances of these holes etc driver and passenger wings 200 / 300 and TD5 on LHD 90 / 110 etc and some pics as well if possible - pretty please ! Hope the above is clearer ?Nige Quote Link to comment Share on other sites More sharing options...
western Posted September 20, 2014 Share Posted September 20, 2014 at outer edge of the drain channel rear of the bonnet aperture. Quote Link to comment Share on other sites More sharing options...
Hybrid_From_Hell Posted September 23, 2014 Author Share Posted September 23, 2014 er ..... HELP ? lol ????? Quote Link to comment Share on other sites More sharing options...
henk Posted September 23, 2014 Share Posted September 23, 2014 This evening as I am not at home for the moment Quote Link to comment Share on other sites More sharing options...
henk Posted September 26, 2014 Share Posted September 26, 2014 2004 90 TD5 LHD https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-xap1/v/t1.0-9/1175031_800017643375851_6099101030429097632_n.jpg?oh=1695bbafd478f36dbecf94e82d14c069&oe=548757AF&__gda__=1422649062_d690adf6c6fe0339775feda0544c2672 Quote Link to comment Share on other sites More sharing options...
Hybrid_From_Hell Posted September 27, 2014 Author Share Posted September 27, 2014 Superb !...can you do the other bolts there and both sides ?? Nige Quote Link to comment Share on other sites More sharing options...
Mo Murphy Posted September 29, 2014 Share Posted September 29, 2014 That's bizarre isn't it ? A tape with no inches on it ! ? Mo Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.