trickydicky Posted May 3, 2016 Share Posted May 3, 2016 iv got a 1990 200tdi 90 defender iv been getting a build up of pressure in the rear drum breaks .on a long drive the break peddle bites at the bottom and ends up at the top and eventualy I can feel the breaks binding .iv had the car 2 years and its allways done this .iv now changed the whole system apart from the valve that's bolted to the bulkhead can anybody tell me what is its function and where can I get one or can it be stripped down .its only connected to the rear drum breaks if that helps .ps sorry for the pic I got it off the net Quote Link to comment Share on other sites More sharing options...
Ex Member Posted May 3, 2016 Share Posted May 3, 2016 http://www.allbrit.de/UNI.cfm?PAGE=757666&SPRACHE=EN Brake valve. NRC8215 No longer manufactured. Might try overhauling it. Quote Link to comment Share on other sites More sharing options...
trickydicky Posted May 3, 2016 Author Share Posted May 3, 2016 thanks for the imfo after a bit of googling it looks like it boosts the pressure to the rear brakes they fitted them to military 110s and a few 90s it sounds like somethings stuck inside Quote Link to comment Share on other sites More sharing options...
western Posted May 3, 2016 Share Posted May 3, 2016 That valve limits the brake pressure to rear so the brakes don't lock up before the front brakes have done the major braking effort & prevents the vehicle swapping ends too, don't think there's much working parts inside, a ball valve in a inclined gallery. Quote Link to comment Share on other sites More sharing options...
Ex Member Posted May 3, 2016 Share Posted May 3, 2016 Yes, as I understand it is a "G" valve. When you stop quickly, it closes off the rear brakes the harder you stop. I would take it apart and clean it out. These are the sort of things that die when people do not flush the brake fluid for a long time. Quote Link to comment Share on other sites More sharing options...
trickydicky Posted May 4, 2016 Author Share Posted May 4, 2016 the only thing I can think it may be is that the ball is getting stuck and stopping the fluid from returning back .every time I put my foot on the brake it build up the pressure until the brakes start to drag.if I put my foot on the pedal hard for a few seconds it seems to correct itself and its only on the back brakes . it may just be some carp in the valve it was an old farm vehicle and we all know how they get abused Quote Link to comment Share on other sites More sharing options...
qwakers Posted May 4, 2016 Share Posted May 4, 2016 more likely you have a collapsing brake pipe or mal-adjusted servo. Quote Link to comment Share on other sites More sharing options...
trickydicky Posted May 4, 2016 Author Share Posted May 4, 2016 all the brake pipes are new and iv adjusted the servo until the pedals at the floor the whole system is new apart from the g valve .it had the problem when I brought it and its not changed no mater what iv changed Quote Link to comment Share on other sites More sharing options...
Scotts90 Posted May 5, 2016 Share Posted May 5, 2016 Is the g-valve plumbed correctly? Front port feeds to rear and side port goes to master cylinder front port...or that's the way mine is plumbed and works fine with the disc rear axle. Quote Link to comment Share on other sites More sharing options...
FridgeFreezer Posted May 6, 2016 Share Posted May 6, 2016 I had a similar problem when I adapted a RR master cylinder & servo to a Series pedal box - the master cylinder needs the pedal actuator to release fully (with a bit of slack) or it will gradually pump up and lock the brakes. In my case, I needed a spacer between the servo & pedal box to allow the shaft some slack. I don't know if there's adjustment in a standard truck but it sounded so similar to what I had I thought I'd mention it - possibly a previous owner has replaced the servo or master cylinder and not got it quite right? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.