De Ranged Posted April 3, 2017 Share Posted April 3, 2017 A while back I asked for information on series hubs for a disk conversion I'm doing on a mate now 100" SII Here ya go, Mazda Series 7-8 Rx7 calipers (4 pot alloy) on a machined BMW X5 disk Not exactly a simple conversion I've got over 12hrs machining per side lol sorry about the blurry pic's camera is a bit cracked Quote Link to comment Share on other sites More sharing options...
De Ranged Posted April 3, 2017 Author Share Posted April 3, 2017 I'm sorry, was in a bit of a rush to get back to the misses to give her, her time and forgot to snap some shots of the disk mount.... if anybody is interested next time I'm in the shed I can get the dimensions for this Cheers Reece Quote Link to comment Share on other sites More sharing options...
Soren Frimodt Posted April 4, 2017 Share Posted April 4, 2017 Looking good as always! Those calipers look nice and compact, there's no way you could put Coiler calipers that far out, they would foul the wheel Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted April 4, 2017 Share Posted April 4, 2017 Those calipers look massive, especially when sat on the bench, nice work on the fab front too. It does confirm to me that there is still no easy way to get discs on a series, unless you swap out the axles entirely for something like Toyota, which of course, may not be easy anyways Props to you for persevering, hope they work for you when up and running Quote Link to comment Share on other sites More sharing options...
Arjan Posted April 4, 2017 Share Posted April 4, 2017 Nice ! Envy your skills. We just used the Zeus kits... Quote Link to comment Share on other sites More sharing options...
De Ranged Posted April 4, 2017 Author Share Posted April 4, 2017 Thanks for the comments The axle swop isn't as easy lol as it has its own compromises most of the local boys just drop hilux axles under them, my mate wanted to run a sals rear so I couldn't match the diffs this was the only answer lol other than a VERY expensive (once its landed in New Zealand!) Zeus kit witch wont match this for performance should he decide to run to larger wheels in the future For the books the calipers are a 4 pot with I think around 5mm less size than the landy 110 pots but due to the size of the disk (dia) I got under there I think they will out perform the standard 110 setup To be honest Arjan if I was still running the shop, given the amount of work involved in these the charge out would be about the same as the Zeus kits Quote Link to comment Share on other sites More sharing options...
xychix Posted June 25, 2017 Share Posted June 25, 2017 The zeus site seems broken down: http://www.zeus.uk.com/ Are they still in business ? Quote Link to comment Share on other sites More sharing options...
Snagger Posted June 25, 2017 Share Posted June 25, 2017 On 04/04/2017 at 11:53 AM, Bowie69 said: It does confirm to me that there is still no easy way to get discs on a series, unless you swap out the axles entirely for something like Toyota, which of course, may not be easy anyways It must be much easier than this, but it's not simple, certainly. The rear axle on a 109 is simple enough, but the spring position on the 88 interferes with the diff housing on a Salisbury and probably needs a complicated shape scalloping from the inboard side of the rhs mount to clear the diff housing on a Rover rear axle, just like the front axle on both wheel bases. Then there is the steering rod clearance over the leaf springs, the custom length drag link and the prop shaft front UJ angle and proximity to the engine mount... Still, I'd take all of that again compared to the effort involved in this! Lovely work, DR. Quote Link to comment Share on other sites More sharing options...
Arjan Posted July 1, 2017 Share Posted July 1, 2017 Zeus seems to be alive and kicking : http://www.zeus.uk.com/index.php " It does confirm to me that there is still no easy way to get discs on a series " Well, the Zeus kit is a direct swop bolt operation and works very well.. But yes, it does cost money.. In the end, it is just a personal choice Quote Link to comment Share on other sites More sharing options...
Bowie69 Posted July 1, 2017 Share Posted July 1, 2017 Absolutely, it does work, and must be good, but it is eye wateringly expensive, compared even to a professionally completed axle swap, which can bring all the other benefits to the table. For everyone and every situation there is an ideal solution Quote Link to comment Share on other sites More sharing options...
Snagger Posted July 2, 2017 Share Posted July 2, 2017 Gremlin did a very thrifty conversion on his 109 using standard LR parts, which would allow people to use bits from breakers (subject to close inspection, I would hope). I think the only custom parts he used were the front caliper brackets that he made up, similar in appearance to Deranged's but slimmer, I think. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.