jules Posted March 8, 2006 Share Posted March 8, 2006 dose anyone know were I can gat a second hand one as new ones are very expensive. needs to heat about 2000 m3 south of England area. Quote Link to comment Share on other sites More sharing options...
andyb Posted March 8, 2006 Share Posted March 8, 2006 You need a licence too. Burn anything else other than engine oil and they tend to smoke a bit as well. Quote Link to comment Share on other sites More sharing options...
jules Posted March 8, 2006 Author Share Posted March 8, 2006 You need a licence too. Burn anything else other than engine oil and they tend to smoke a bit as well. It for a car work shop so it should only be used engine oil I didn't know you needed a licence for them I would think he should get one with ease as its been a workshop for 15years or so. Quote Link to comment Share on other sites More sharing options...
imspanners Posted March 8, 2006 Share Posted March 8, 2006 The licence is around £120 per annum: UkAutotalk waste heater discussion Quote Link to comment Share on other sites More sharing options...
jules Posted March 8, 2006 Author Share Posted March 8, 2006 The licence is around £120 per annum:UkAutotalk waste heater discussion mmm the waste transfer issue I don't know what he dose at the moment. I have files full on site for the skips and asbestos I forgot that normal businesses need them to. Quote Link to comment Share on other sites More sharing options...
Steve Hiatt Posted March 8, 2006 Share Posted March 8, 2006 I have a home made one and got a slap from the Environment man. He said I should have a proper one. I use wood now Quote Link to comment Share on other sites More sharing options...
simonr Posted March 8, 2006 Share Posted March 8, 2006 I have a home made one and got a slap from the Environment man. He said I should have a proper one. I use wood now Steve, How did your home made one operate? Si Quote Link to comment Share on other sites More sharing options...
Steve Hiatt Posted March 8, 2006 Share Posted March 8, 2006 It's a wood burner I made from three tractor rims, centres removed, and stood on end. I put in a 10mm oil feed that drips onto the fire. It will run totally on oil using a few bits of wood as a wick, or if you have a good wood fire going it adds extra heat. It does burn clean when hot, probably more suitable for a farm than an industrial estate. Quote Link to comment Share on other sites More sharing options...
simonr Posted March 8, 2006 Share Posted March 8, 2006 It's a wood burner I made from three tractor rims, centres removed, and stood on end.I put in a 10mm oil feed that drips onto the fire. It will run totally on oil using a few bits of wood as a wick, or if you have a good wood fire going it adds extra heat. It does burn clean when hot, probably more suitable for a farm than an industrial estate. Ah, a simple one then! I have come across designs using petrol injectors and burning a fine mist of oil. Hoped it might be something like that! Si Quote Link to comment Share on other sites More sharing options...
Steve Hiatt Posted March 8, 2006 Share Posted March 8, 2006 Have a look at the old grain dryer burners. They use presurised fuel that turns a small fan, atomising the fuel Quote Link to comment Share on other sites More sharing options...
robhybrid Posted March 16, 2006 Share Posted March 16, 2006 Thought I would show you my waste oil burner using 2 landrover brake drums. The pipe going up glows red and gives off loads of heat The smoke is bad when you initially light it but it burns clean once it is hot. The bottom drum has had all the holes welded up to create a large dish to hold the oil. There are a lot of holes (20ish) 10mm around the bottom pipe about 1/2" up from the top brake drum. There are 3 holes 10mm about 1'6" up the first pipe. The pipe diamiter is a close fit to the center of the brake drum. The ferocity? of the fire is controlled by blocking up or unblocking the top brake drum stud holes. I 3/4 fill the bottom drum with waste oil then add a splash of petrol and drop a burning rag onto it then put the top drum back on. Yes I have burnt the hairs of the back of my hands and sindged my fringe and eye brows experementing Quote Link to comment Share on other sites More sharing options...
jules Posted March 16, 2006 Author Share Posted March 16, 2006 Thought I would show you my waste oil burner using 2 landrover brake drums. Yes I have burnt the hairs of the back of my hands and sindged my fringe and eye brows experementing I though I was mad with fire Quote Link to comment Share on other sites More sharing options...
robhybrid Posted March 16, 2006 Share Posted March 16, 2006 the flash of the camera stops you from seeing how red the pipes are glowing Quote Link to comment Share on other sites More sharing options...
Turbocharger Posted March 16, 2006 Share Posted March 16, 2006 My dad has a more conventional oil burner made from an old propane cylinder. It smokes - lots. Rob's looks like a much more dramatic solution though - where do you put the oil in (continuously)? Quote Link to comment Share on other sites More sharing options...
geoffbeaumont Posted March 16, 2006 Share Posted March 16, 2006 I though I was mad with fire Looks quite tame by Rob's standards Last time I was up there his wood burner and most of its chimney was glowing red with the aid of a bit of old oil Quote Link to comment Share on other sites More sharing options...
robhybrid Posted March 16, 2006 Share Posted March 16, 2006 My dad has a more conventional oil burner made from an old propane cylinder. It smokes - lots. Rob's looks like a much more dramatic solution though - where do you put the oil in (continuously)? I only fill the bottom pan then re fill once it has gone out 3/4 - 1 hour. I have seen a burner like this with a long length of brake pipe with a tap from a 5 gallon drum on a stand feeding in through one of the stud holes. The tap was used to controll the oil flow to be sufficient to keep the bottom of the pan covered in oil. Quote Link to comment Share on other sites More sharing options...
Steve Hiatt Posted March 17, 2006 Share Posted March 17, 2006 Thats how I used to feed mine until the Environment man paid a visit. I did go to a bigger bore as it used to block up, maybe I should change my oil more often. Quote Link to comment Share on other sites More sharing options...
ormus Posted March 24, 2006 Share Posted March 24, 2006 http://journeytoforever.org/biofuel_librar...h/me4.html#mwoh heres a link to make your own heater. enjoy. hope this helps you. Quote Link to comment Share on other sites More sharing options...
Spike Posted September 2, 2007 Share Posted September 2, 2007 Here's a photo demonstrating how simple an oil heater can be. I have had a drip fed waste oil heater heating my house for eight years now, and although it is not pretty, there is a very good trade off between looks and costs. Prior to fitting the heater, I used to cut and burn 25-6 tons of firewood every winter, the cutting and splitting of which severely cut into my leisure time. The photo above was sent to me by a gentleman in New Zealand who has since built and installed a modified and much prettier version of my own. He assembled this in his back garden just to test the principle because as he admitted later he did not believe that it was so simple. The lower end of the flue is made from an old cylinder liner from a Mack truck and being cast iron, is easy to drill, highly resistant to heat damage and cheap and easy to replace if you need to. I have not replaced mine in eight years and it is not showing any signs of burning out. There are four versions of my heater now in use that I know of. One heats a lap pool used by a paraplegic, the others are heating homes and a workshop. Regardless of what you may have been told, they can be made to work very successfully without smoke or unpleasant odours, although they can take a bit of mucking about to fine tune as they do not have a great range of clean burning temperatures and need to be set up to burn cleanly at or near the temperature best for your purposes. As for licenses, there is no provision for licensing here in Australia, but if asked I would say, "Don't ask and don't tell" what the authorities are unaware of is obviously doing little or no harm. A bit of history on mine can be found here: http://www.geocities.com/senojekips/shed.htm Quote Link to comment Share on other sites More sharing options...
Spike Posted September 10, 2007 Share Posted September 10, 2007 Here's the next progression, still quite crude but getting a few of the rough edges knocked off. Using two worn out truck sized brake drums, which can be obtained free at your nearest trucking company. Quote Link to comment Share on other sites More sharing options...
Spike Posted September 11, 2007 Share Posted September 11, 2007 Here it is in it's finished form. Cheap heat! This is NOT my heater, but an improved version. It is owned by, and all of the work was done by a New Zealand Policeman. I think the standard of work is a credit to him. Quote Link to comment Share on other sites More sharing options...
Spike Posted May 18, 2009 Share Posted May 18, 2009 After 11 years of use I have finally been shamed into giving my heater a "birthday" and implementing the improvements I was telling others to try. This is the testing done prior to moving it back inside. And here it is in use. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.