Defender guys.
Is PRC6021 the correct early speedo cable to fit to the LT230 and do the early speedometers have the same push on plastic cable connection in the rear as the series ones?
Mine will be a V8 and is tax and MOT exempt but I still get it tested. You might argue that a vehicle that isn’t used much could be higher risk than one that’s used regularly and has all its moving parts free. I’m thinking more of sticking brakes etc and perishable items such as brake lines and hoses.
Just a thought.
Cheers, yes the existing drive is still there and it’s a brown one. I may just swap it for the Defender one anyway whilst it’s out of the box. Question is though will my series speedo cable connect to the Defender drive gear? I’m sure I have my old cable knocking about somewhere so I’ll try and dig it out unless someone who’s already fitted a Defender box into their Series can clarify?
On a similar topic, does anyone know if there is a speedo cable that can be used with an LT230 and a Series 3 speedometer?
My transfer box (off a Disco) had the electronic sender fitted to the speedo drive gear so presumably I will need to change that for another mechanical drive gear off a Defender on 7.50 size tyres and 3.54 diffs?
Not sure if this has already been muted but could you fit an adapter in place of where the cable operated heater valve goes on a 2.25? On the picture of the 2.5 it looks like the valve is removed and the heater hose goes direct to the head. If you could make an in-line adapter then a sender could easily be screwed into it.
The last one I fitted went on the inlet manifold but that was for a Cosworth engine in my Capri and there was already a tapped port for it. I believe as close to the inlet as possible would be preferable. Remind me what ECU you will be using to run the engine, is it MS?
Getting an unlocked ECU to run a stand-alone THOR engine is simple enough but then don’t you end up having to modify the wiring loom to get it all to run? Isn’t this one of the reasons (besides tuning capability) that people opt for the MS kit?
As I understand it it’s not simply a case of putting power to the unlocked ECU is it? On the Tornado website they state that they can provide wiring details but that’s as far as it goes and I can’t find a pin out diagram to see what exactly is involved.
I’ve never come across a comparison between the performance of an unlocked standard ECU against a ‘standard tune’ (for general road use) MS kit but it would be interesting to see.
I think having this sort of information available would allow people to make more informed decisions as no doubt there are pros and cons to each system.
Problem I have is that I’d like to try and keep the 45 year old patina if possible whilst protecting things like the steel bulkhead that are showing early signs of light surface rust. If I repaint the whole vehicle then it will take a good few years to lose it’s fresh look.
The alloy panels aren’t too bad to look after but the bulkhead and front panel will take a bit more thought. I thought that the Owatrol would do the job so I might give it a try as the car will be garaged when not in use. I can paint the internal surfaces but just keep the external ones as they are and reapply as and when.
Yes, I won’t be needing it and it looked a bit daft with the empty bracket although the coffee table idea was floated for a while 😊
I need to get to a rolling chassis stage first before I can install the engine and order the MS from Nige👍
Does anyone have any experience or feedback of using Owatrol oil to preserve bodywork patina whilst providing anti corrosion protection to exposed ferrous metal surfaces such as the bulkhead?
Im really in two minds whether to paint or preserve 🤷♂️
Is there any chance that someone has a front and rear axle sat in their garage from which they could take the hub wheel face to wheel face measurements for me please?
Off topic I know but I remember fitting a Di engine to a 109 many years ago. Straightforward enough as a conversion and pulled the vehicle along quite well but one of the noisiest engines I’ve come across in a Landrover.