steve200TDi

I will check for you. Steve

So I've been getting it ready to take to Summer Sisters, which now only a week away! I've fitted a new silver top Facet fuel pump. And added some storage: There will be plastic snap lid boxes going in as well. You can never have enough storage! New CB radio, apparently the smallest....in the world! And matching red antenna! A new windscreen! And the rear winch tray is in! Just the rear winch to fit, add a few fuses, add the antenna, set the CB radio up, put some fuel in it! And load it all up next week for Wales inbound Steve

Hi, There quite small, so I think they're M6, but that's with out checking! There not a fancy thread. Steve

Thanks for the advice Dave, I was thinking about it, but a lot of hassle cutting a hole in the top of the tank, so just for ease I opted for the low pressure pump and swirl pot. I wont go down the in tank pump route then! Yes, I saw the Comp this weekend and the venue change, but think it's still too soon, so it'll be later in the year for sure! Steve

That's fine Jon! I was even thinking about splashing out on a new one, but still unsure of which one to get....red top...silver top...who knows! Steve

So last week I finally gathered all the parts I needed to revise the fuel system. One shiny swirl pot Fitted with a low pressure Facet pump (Thanks Jon!) and Bosch 044, albeit non genuine, but I thought the 'high flow' unit I previously had, may have indeed been to high a flow! All plumbed in as per Jon's and usual convention. After priming the system it seem to start ok, with the standard Lucas 10 second fuel pump prime system. So took it to Slindon at the weekend......... And it ran all day! here's a video: Things I found out... The Facet pump got very hot to start with, so hot I almost burnt myself checking the temperature! It did seem to cool down and by the afternoon it was fine. So maybe it just needed some running in time. I notice the end cap uncrews, so maybe worth a look see and a rebuild! the pattern Bosch 044 was quite noisy by the end of the day, so tempted to swap it for the high flow unit which was quieter or something else. The car got up to temperature and warmer as it was a hot day. This is normally the time it cuts out, but it didn't! The fuel tamp is still hot, but the pumps are cool. The air flow around the back of the vehicle isn't idea, so I have some ideas: - A small scoop on the boot to divert air down over the swirl pot and pumps, easy to do and may help. - A heat shield in front of the fuel tank (engine side) as because the vehicle has under body skid plates, all the hot air from the engine hasn't got anywhere to go and just sits behind the tank, so maybe some hole to try and get rid of some of the hot air is needed. This has definitely helped, so I'm going to keep trying to improve it and get it prepared for Summer Sisters! Steve

Well I took it for another outing to Slindon at the weekend, but sadly the issue is still there, so it's not the fuel pressure regulator! The fuel is getting hot, so it could be vaporising or staving the fuel pump of fuel. The inline fuel pump I have may be to highly rated for the engine and so pumping most of the fuel back into the tank which wont help with aeration. So my next plan is to: - fit a facet fuel pump to suck the fuel out of the tank (Thanks John!) - Fit a fuel swirl pot - reroute the fuel lines somewhere cooler - Maybe even make the return line larger so as not to make a restriction I was also thinking of fitting an in tank fuel pump, as that could alleviate some of the problems too, but it's a lot of effort cutting a hole in the tank if I don't know for certain it will work, this could be an improvement in the future though. Steve

Also the handbrake is attached to the rear propshaft hence no rotational movement. Steve

Glad you got it sorted! Steve

Or one of Davids budget ropes: http://www.goodwinch.com/shop/budget-bowrope/budget-bowrope-10mm-x-27-5m90-or-30-5m/ You can't go wrong with his products! Steve

I did see this. I know a lot of people now use the synthetic, but there are still people who only use there winch occasional/now and again or who still want to use steel cable, so I don't know where people stand with that! Steve

Haha, ok. Yes, it doesn't help having the spark plug hole at an angle otherwise it would be straight forward to use a dial test indicator (dti) http://www.mini-lathe.com/Measurement/Dial_indicators/Dial_indicators.htm Steve

If you have a DTi and steel disc (ideally with degrees on it) you can find the exact TDC. If you have the kit, then why not do it! If you had a cable tie with graduated marks on you could then work out a set piston height each side of TDC and then you can work out exact TDC. Hopefully this is making sense! Steve

Now this looks handy! http://www.ebay.co.uk/itm/Emco-Star-Band-Saw-Rip-Saw-Disk-Sander-Belt-Sander-Multi-Machine-/182064788074?hash=item2a63e8326a:g:rREAAOSwZtJW8vKk

It appears so! Hot water, preferably boiling to leave to soak for a bit and then once finished (or cold) throw it away! Steve

I've just cleaned all my diff centres and ARBs with this stuff!: https://www.machinemart.co.uk/p/5-litre-parts-washer-concentrated/ I have one of the small parts washers, but last time I used it I ditched the mezzanine level and didn't use the 10 or so litres it recommends because of the following: - I put 0.5 litre or so of the fluid in the tank and topped up with boiling water with the parts in. - Didn't use the parts washer pump! - just used a small paint brush/toothbrush. It seems to work a lot better the hotter the water is! Ok, it's not the best and I use parafin at work, but it stinks! So for a quick wash at home this is ideal. As I said it works best with boiling water and then wash the parts quickly after as when the water cools off it's useless. A couple of times I've topped up with another kettle full of water so you can use the same stuff again. Also I've tried reheating it too - that didn't work either and is more hassle than it's worth! Steve And it smells nice too! Orangy I think!

Mmm... Different, it's certainly different and in some peoples eye, it may be horrible.. http://www.ebay.co.uk/itm/Land-Rover-110-project-build-/121934849024?hash=item1c63e22400:g:vHcAAOSwKtlWjpKO Steve

As I've been replacing my transfer box myself, I thought I'd take a few photos for you. It was a bit dark as you can see! No diff lock: Difflock (you can see the bit you arrowed in red does move a little): But also there's an arm that rotates to engage and disengage the diff lock. This may be sticking or may need the vehicle to roll slightly for it to engage. No diff lock: Diff lock: Hope this helps and there is also adjustment on the pivot. You can move it in or out with the lock nut to gain more throw. Steve

You may need the car slightly rolling to get it in difflock. Steve

I think it varies depending on time of year, so Yes, I'm afraid there maybe Midges, but don't let that put you off! Steve

Hmmmm, I don't think that's right Chris! Steve

Thanks Dave, they sound like good events, just a shame I working on the first two dates, but I might try the Trojan Trophy later in the year. Thanks Dave (Another Dave!) Sounds also like a good event, but just a shame that Yorkshire (for me) is so far away! Steve

Yes, I have heard of stories like that. I think that maybe what happened to the Mud Monsters series this year! It is very difficult to organise an event if you don't know how many people are coming as it's a big commitment! In that case i'll try and go to event already on this year and support them. Come on people! You too! Steve

I've heard of terratagging, but what exactly is it? Steve

Nice garage door too! Steve