upnover4x4 Posted October 26, 2008 Share Posted October 26, 2008 Is there a definitive means of identifying tranfer boxes by just looking at them? I cant determine the origin of my tbox & have gone through my manuals to no avail. I assume it can be identified from the serial number but have not yet found that due to contamination. I need to identify what ratio the tbox is to correct the gearing due to tyre size. Thanks Adrian Quote Link to comment Share on other sites More sharing options...
Les Henson Posted October 26, 2008 Share Posted October 26, 2008 Slightly to the left of the handbrake drum there should be a sticker which will give you the ratio of it. Is it no longer there? Look on Ashcrofts site - there's a mine of information there that will help you identify it. Les. Quote Link to comment Share on other sites More sharing options...
upnover4x4 Posted October 26, 2008 Author Share Posted October 26, 2008 Thanks for that Les, found the number, but know it doesnt correspond to the ashcroft tech sheets. Will give them a ring & verify. Adrian Quote Link to comment Share on other sites More sharing options...
western Posted October 26, 2008 Share Posted October 26, 2008 post up the serial number should start with something like 22D Quote Link to comment Share on other sites More sharing options...
andyb Posted October 26, 2008 Share Posted October 26, 2008 This following was posted on Mud-Club a couple of days ago, thought it would be useful here. The LT 230 was fitted to all 5 speed Defenders, all Discos and the RR Classic up to 1988. The serial number will be stamped in one of 2 possible places, either on the bottom left of the main casing or on the earlier vehicles right at the bottom of the left hand side face of the main casing obscured by the exhaust pipe in which case you will need a knife (to scrape the muck off) and a mirror. You are looking for Eg. "28D123456E, you are interested in the first two and the last, i.e. a "28E". The Borg Warner serial number is printed on a plate at the bottom middle of the rear face. The numbers will look like this Model No: 13-61-005. The numbers and letters after the model number will vary from type to type so you will need to know all the numbers or letters shown. 12D = 1.667 LT 230R, 13D = 1.410 LT 230R, 14D = 1.003 LT 230R, 15D = 1.192 LT 230R, 20D = 1.667 (2.5 N/A 110), 22D = 1.410 (all 4Cyl 90/110 bar above), 25D = 1.410 (V8 110 LT 85), 26D = 1.003 (RR Classic 3 speed auto), 27D = 1.192 (early RR Classic), 28D = 1.222 (RR and Disco I), 29D = 1.192 (V8 90 LT 85), 32D = 1.222, 34D = 1.410 (2.0 Disco I), 36D = 1.211, 38D = 1.211, 40D = 1.211 (NAS/Japan 90&Disco), 41D = 1.211 (Disco II, diff lock stud), 42D = 1.211 (Disco II, diff lock stud), 43D = 1.410 (90/110 TD5), 57D = 1.410 (90/110 TD5), 61D = 1.211, 62D = 1.211, 68D = 1.211, 69D = 1.211, 70D = 1.211 (Disco II, no diff lock) Quote Link to comment Share on other sites More sharing options...
TomG Posted October 26, 2008 Share Posted October 26, 2008 You can also pop the bottom cover plate off and dot a tooth with a bit of paint then with a wheel a wheel of the front & rear axle jacked off the ground, the transfer box in difflock, engage high ratio with the main gearbox in neutral, turn the rear prop by hand and count the teeth on each of the teeth from the input shaft through the intermediate gears to high range. A bit of maths will then give you the ratio. Quote Link to comment Share on other sites More sharing options...
Paddy_SP Posted October 28, 2008 Share Posted October 28, 2008 My LT230 had a ratio sticker, but no serial number. At first, I thought it was simply hidden by crud, but as I've since jetwashed it, then stripped and put the cases in the parts washer and finally in the dishwasher (hee hee), I can now state categorically that there is no serial number; I have no idea why...? Quote Link to comment Share on other sites More sharing options...
western Posted October 28, 2008 Share Posted October 28, 2008 must be a replacement at sometime & had it's original number ground off. Quote Link to comment Share on other sites More sharing options...
upnover4x4 Posted October 28, 2008 Author Share Posted October 28, 2008 This is the bit that confuses me , the serial number is 13D031015A. According to the ashroft site it would translate to a 13A! But does not specify this derivative of number. Not to worried now as realised that regarless of what transfer box is fitted, low raio stays the same. Does anybody know of a supplier of lower ratio gearsets? Adrian Quote Link to comment Share on other sites More sharing options...
western Posted October 28, 2008 Share Posted October 28, 2008 that one would be a 13D suffix A not a 13A. nearly all transfer boxes have 2 numbers & letter prefix then the serial number with a letter suffiix, the prefiix idents the ratio in the box. from Ashcrofts pages for example 13D = 1.410 LT 230R mines a 22D suffix C which comes out to 22D = 1.410 (all 4Cyl 90/110 bar above), the suffix idents any production changes. Quote Link to comment Share on other sites More sharing options...
upnover4x4 Posted October 28, 2008 Author Share Posted October 28, 2008 Thanks Ralph, your knowledge is endless..... adrian Quote Link to comment Share on other sites More sharing options...
western Posted October 28, 2008 Share Posted October 28, 2008 got some of that info from Mr Ashcrofts site how close to camborne are you ? might need a hand to refit my transfer box later this week. Quote Link to comment Share on other sites More sharing options...
ashtrans Posted October 29, 2008 Share Posted October 29, 2008 or to ID the ratio you can use the technical method which requires an adjustable spanner and a bit if cardboard, using the spanner put it in diff lock and high ratio, stuff a bit of cardboard in the input gear hole, mark a prop drive flange and turn it 1 rev whilst counting how many times the cardboard turns in the input, if it's just less than 1 1/4 it's a 1.222, just less than 1.5 it's a 1.410 ! Quote Link to comment Share on other sites More sharing options...
HoSS Posted October 29, 2008 Share Posted October 29, 2008 Is there a definitive means of identifying tranfer boxes by just looking at them? Yes. Under the landy, near the centre, attached to the gearbox - is a large aluminium/mud coloured metal lump. Thats the transfer box. Quote Link to comment Share on other sites More sharing options...
crazyfarmerboy Posted November 1, 2008 Share Posted November 1, 2008 if there is no sticker that tells you there should be a serial number. i think it is the first 2 sybols and last one that tells you. well after you scrape of the top layer of mud and oil. Quote Link to comment Share on other sites More sharing options...
rusty_wingnut Posted November 3, 2008 Share Posted November 3, 2008 i have got a Borg Warner viscous unit but am unsure of the ratio, are there multiple ratios for these or just one? Quote Link to comment Share on other sites More sharing options...
ashtrans Posted November 3, 2008 Share Posted November 3, 2008 Hi, just one ratio, 1.206, Quote Link to comment Share on other sites More sharing options...
rusty_wingnut Posted November 3, 2008 Share Posted November 3, 2008 Superb thanks Dave! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.