done the same on my 300tdi
fitted a darton alloy breather and piped it into a catch tank
one thing to remember tho is if you go wading a lot the vent on the catch tank could let water in to your engine oil
rob
Hi
the t series engine has hydralic tappets mounted under the cams so no adjustments or push rods
easy way to sort out what ones have gone soft remove cam covers and press the lifters down with a screw driver to check for any soft ones (with cam lobe pointing upwards)
rob
must be hinge time as i just did mine too!!! (got a pair of new in packs off ebay for £10.55 delivered )
defo take the spare off!!!!!!!!
get new proper rivits for the end plate and a big a$$ rivit gun to do them with
a second pait of hands is usefull
rob
dont be so soft
but yes i would have checked the gearbox and transfer box oil levels (well changed them actually) very soon after purchase (as you was told to do when you first got the car!!)
most truck/commercial garages have hot tank washers too so ask at your local one
i used to work in a merc one and used to put my rangies wheels in there to clean them
(if its delicate items they need restraining as the basket spins like crazy and turn the water jet temps down they can go up to 180 degs (approx))
rob
i do check my cars levels after its been in a garage yes
and i allways go over my new purchase with a fine tooth comb regardless of what the seller says its had done!!
and with the last paragraph there yes people saying you have got a pup is unhelpfull but then thats there opinion that they are entitled to
rob
yes those rims will be fine for your new tyres (much better than having tubes in them too)
your tyres are 235mm wide so recommended for a 6 to 7 inch rim
great choice in tyres too
rob
hi western
i think you have miss interpreted what he is after doing
i took it that he wants fogs to come on with main beam for extra lighting on mains(how i took the question anyway)
rob
265 75 16 will be needing a arch trim and suspension lift
if its bog stock then 255 65 16 will just fit but 235 70 16 is safest if used off road with plenty of articulation
rob
could be the chatter between the gearbox and transfer box
have heard a few that do this with no ill effect and local independant lr centre say its ok too
rob
100% agree with that
use to work in a landrover/rover main dealer and i had the above gun every one else has snap on ones and mine was the only one that could undo honda crank pully bolts unaided
snap on guns = poo im afraid (heavy/noisy/and no where near there rated output)
rob
not quiet the same but my shogun snapped a tailgate hinge pin and as a new hinge was 130 quid i took the old one to a local engineering place and 20 quid later my hinge had a nice shiney stainless pin
no probs chap
i 'removed' mine after it stopped it starting a few times
there have been a few threads on the ddis set up and general concensus is its a touch unreliable
just to note your car wont have a spider for the imobiliser as the box on the pump does it
let us know how you get on
Rob
thats a ddis immobiliser box (and its poo)
carefully break that off with a gentle hammer and chisel (it has break off security bolts fitted holding it on with a bar behind the solenoid)
then connect the centre wire to the top of the solenoid (after you have fitted a ring connector) thats under it jobs a good one
rob
this guy has fitted them on a disco so maybe worth a read to see if that helps
http://www.overland-rovers.com/ralphs-pages/vehicle-modifications/112-fitting-extended-range-fuel-tanks-to-a-discovery-1.html
rob
sounds like fuel drain down
best way to be sure is run a pipe into a can of diesel if prolem goes away you have a hole in a pipe somewhere allowing air in
first place to look is sender unit in the tank where the pipes come out
also check the injector leak off pipes too
yeah i thought that as mine is a 3 hole
and every one i have seen in the past has had holes in it hence this throwing me a touch as i
wasnt aware of a no hole gasket untill today
rob
hi all
my mates disco 300 tdi headgasket is chuffing at the back of the head so we need to order parts up to do the job but cant find any notches on his gasket???
head is still fitted as car is in daily use
what do i do now?
thanks rob