Nigelw Posted December 13, 2013 Share Posted December 13, 2013 Gotta do some reasonably precise cutting of some tube, now I am not a bad free hand cutter with my 9" but both tubes need cut paralel and square. Idea so far, clamp the work piece on a piece of flat plate, fit a metal cutting disc on my circular saw and cut both tubes near identical, or is there a better way? Quote Link to comment Share on other sites More sharing options...
cookie64 Posted December 13, 2013 Share Posted December 13, 2013 laser cutting is very cheap and easy Quote Link to comment Share on other sites More sharing options...
steve b Posted December 13, 2013 Share Posted December 13, 2013 ....and rarely available in the home workshop if you get a sheet of A4 paper and wrap it tightly round the tube and line up the edge as it comes back on itself and continue until its all on then tape it the edge of the paper will be dead square to the tube A 4 1/2" with a thin slit disc will be much easier to steer too hth Steveb Quote Link to comment Share on other sites More sharing options...
Jocklandjohn Posted December 13, 2013 Share Posted December 13, 2013 I've been cutting box and tube on a small circular saw with a metal blade with a very good degree of accuracy. If you get it well clamped and levelled its possible to do pretty good job. Quote Link to comment Share on other sites More sharing options...
miketomcat Posted December 13, 2013 Share Posted December 13, 2013 ....and rarely available in the home workshop if you get a sheet of A4 paper and wrap it tightly round the tube and line up the edge as it comes back on itself and continue until its all on then tape it the edge of the paper will be dead square to the tube A 4 1/2" with a thin slit disc will be much easier to steer too hth Steveb 2" masking tape pulled tight and rolled round works well to. Mike Quote Link to comment Share on other sites More sharing options...
Anderzander Posted December 13, 2013 Share Posted December 13, 2013 I have a cheap circular chop saw ... I wonder if I can get cutting discs to fit it ..... Never thought that might even be a possibility. Quote Link to comment Share on other sites More sharing options...
FridgeFreezer Posted December 13, 2013 Share Posted December 13, 2013 +1 for A4 paper wrapped round, or a chop saw. Quote Link to comment Share on other sites More sharing options...
TheRecklessEngineer Posted December 13, 2013 Share Posted December 13, 2013 Again, I've used A4 in the past. Works very nicely. Quote Link to comment Share on other sites More sharing options...
Tanuki Posted December 13, 2013 Share Posted December 13, 2013 I like the little "wheel cutters" that plumbers/electricians use: they give a good clean cut with no burring. This sort of thing: http://www.tradecounterdirect.com/plumbing-tools/gas-pipe-drain-installation/pipe-cutters/super-2-steel-pipe-cutter-70045_2in.html Quote Link to comment Share on other sites More sharing options...
Stevie D Posted December 13, 2013 Share Posted December 13, 2013 Paper /masking tape trick works well with a jubilee clip as a bit of a hard(er) guide too. Steve Quote Link to comment Share on other sites More sharing options...
vulcan bomber Posted December 13, 2013 Share Posted December 13, 2013 A lathe..... Quote Link to comment Share on other sites More sharing options...
Nigelw Posted December 13, 2013 Author Share Posted December 13, 2013 Well will be doing the job tomorrow night as I now have to order and wait for parts to carry on with rusty body work so will be testing out a couple of the methods given and will most likely take some pics too Quote Link to comment Share on other sites More sharing options...
greenstream Posted December 14, 2013 Share Posted December 14, 2013 Depending of the diameter, then used/empty rolls from toiletpaper or the like is of good use ;-) Quote Link to comment Share on other sites More sharing options...
discomikey Posted December 14, 2013 Share Posted December 14, 2013 Jubilee clips. Works as a guide and if cut manually with a hacksaw the blade seems to not want to cut into the clip, only.follow it a grinder would just eat the clip though although would still work as a quick precise guide. Quote Link to comment Share on other sites More sharing options...
jbs Posted December 14, 2013 Share Posted December 14, 2013 I have a cheap circular chop saw ... I wonder if I can get cutting discs to fit it ..... Never thought that might even be a possibility. I used to use-before I found an Industrial chop saw with a coolant pump at Newbury, a wood chop saw with the original wood circular saw disk removed and 12" metal cutting disks on it to replace the wood disk I removed-this was ok but caused a fair few sparks and also a lot of dust from the disk too hth John Quote Link to comment Share on other sites More sharing options...
Nigelw Posted December 15, 2013 Author Share Posted December 15, 2013 Forgot to do the photos but the circular saw worked very well on my test pieces as some dumb mother hubbard had not yet bent my two pieces of tube that will make my project but I had enough time to try but not enough to do anything productive as parts not yet here, perhaps tonight I will cut the "A" bar and remember to do pictures Need a bit more measuring as not sure the winch will fit in or come out for that matter once welded on? Could be a solid means of security I suppose if they actually have to remove the entire bumper to get to the winch? And welded on bumper bolts too should be safe enough Will post up when I cut properly Quote Link to comment Share on other sites More sharing options...
dm7288 Posted December 15, 2013 Share Posted December 15, 2013 The rage chop saw is a cost effective piece of kit if you are doing a refurb, cuts steel, aluminium, wood etc very well.. http://www.evolutionpowertools.com/uk/build/rage4.php you can also mitre precise angles if you use an angle gauge against the blade to set the cut, worked well on a kit car chassis I built with a lot of compound angles involved.. Quote Link to comment Share on other sites More sharing options...
ballcock Posted December 15, 2013 Share Posted December 15, 2013 I bought a Rage saw from Aldi a few years ago excellent piece of kit. Funny that I bought it to make a car chassis as well. Quote Link to comment Share on other sites More sharing options...
Cynic-al Posted December 17, 2013 Share Posted December 17, 2013 I have a cut off saw and found keeping things level difficult with long stock so ended up with a small table on wheels the same height as the bed of the saw so I could move it depending on the length of the stock. Only works with a level floor though. To be honest most of the time I go with the paper or tape method and a grinder as it's easier than moving the stock to the saw. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.