Giles
Settled In-
Posts
124 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Blogs
Everything posted by Giles
-
Universal electrics for old cars
Giles replied to Sigi_H's topic in Modified Vehicle Builds & Special Projects
Take it easy, all the best for your recovery and get well soon !! -
Hi there, Is it a soft top ??? I find they can be prone to exhaust getting in ... nothing else helpful to add tho ( : Good luck sorting it !
-
Zut ! My go-to for this kinda stuff is to remove, clean/lightly sand etc., and replace all chassis/gearbox/engine earths + the main battery connections & earth lead. Cheaper and quicker than anything else, plus seems like a good way to start fault-finding Bon courage, bonne année et bonne route
-
Exhaust 'puff' occurring, any ideas of cause?
Giles replied to Jocklandjohn's topic in Defender Forum (1983 - 2016)
I was talking to an old-school Bosch pump rebuilder in Germany t'other day and he also recommended 1% cheap engine oil with every fill .... Think I might do this ... -
Dude, everybody's clearly delighted to 'see' you recovered and back here - all the best to you and yr family for the future !!!!
-
It fits snug (but only to the sheet ally !!) right up in the corners just exactly like @stevebus says. You also have to cut a larger hole in the body cappings for the main hoop to fit....
-
+1 for Haix - once you get used to the thick soles !
-
How to replace the throttle spindle seal on a Tdi Injection pump
Giles replied to simonb's topic in International Forum
Strange how things go.... I've got a truck with a bosch EP/VA pump that's started leaking from the shaft... I know they're not the same pump, but I bet they are really really similar... reading this made my mind up - I've just ordered the seal kit . Thanks Simon and others for reminding me that diy is the best route (usually!) -
French Crit'Air sticker and old vehicles?
Giles replied to FridgeFreezer's topic in International Forum
Bonjour, Each city sets its own rules, so what happens in Rouen stays in Rouen. I'll be going in and out of Toulouse several times over the coming days in vehicles that are banned from the LEZ - nobody will check, complain or fine me. Perhaps Rouen is the same ? -
Rear wiring loom colour check 1993 90
Giles replied to Mossberg's topic in Defender Forum (1983 - 2016)
Like Western-guru I have also got my loom outside in convoluted tube. What I like best is the confidence there won't be weird shorts/blown fuses where the barely protected loom rubs through on sharp bits somewhere inside the chassis... -
And... as you can see from Miketomcat's photo, above, you hardly need to raise the back end at all, only a tiny bit. It's the front shock towers that are the high point for rolling the chassis in and out... Go for it...
-
That's something we all love to hear... "shrink and go " sounds great. Congrats
-
200tdi suspect head gasket failure? thoughts...
Giles replied to Maverik's topic in Defender Forum (1983 - 2016)
I bet that's a relief / feels good ! Bonne route -
I have Camozzi fittings too - they cost me just over 2€ each with the vat. It's much better to get the swivel ones, not the fixed ones on the GL site, as this makes it way easier to remove for maintenance, pipe re-routing etc. FYI, if it isn't obvious, the standard LR tube is 6mm and pushes straight in
-
Any tips on fitting a hard top to a soft top?
Giles replied to Phill S's topic in Defender Forum (1983 - 2016)
Hi there, IFAIK there are also special washers for these that have offset slots (or something like that) in them for fine-tuning yer panels.... -
Hi, You need some bushes There should be two in total at the bottom of each damper: one on either side of the spring plate thing. The part no. is 552818 .... good luck !
-
Coolant expansion tank connection
Giles replied to Kevinstraub11's topic in Defender Forum (1983 - 2016)
I'm guessing - no 12j to hand - that it's an overflow kinda thing that should have a short piece of hose attached to route any coolant out, down and away ... -
Experiences with combined pintle hitch and ball hitch?
Giles replied to elbekko's topic in International Forum
i've got one with a DB slider on a 110 - they stick out a bit so make a much better rear step than the DB pintle shown . Only comment really would be to double-check the hole pattern before ordering! -
Looking for a carrier that can transport a pallet to France.
Giles replied to Victor Normandy's topic in International Forum
I've never met George but do know of him cos he has/had a place nearby. Quite a few Brits have used him and I've never heard a complaint. -
If you end up wanting a staging post (or Fr language help)? 50 mins north of toulouse, just ask
-
Congrats, I bet you're well chuffed, that looks tidy
-
I formed the (perhaps mistaken) idea that some were coming from Otokar in Turkey ??
-
Best Online Defender Parts Dealer in EU?
Giles replied to driveallknight's topic in International Forum
I know of and have occasionally used Landypoint.fr - long-standing knowledgeable specialists who do triumph + jag too . You'd think that maybe Spain (cos of Santana etc.) might offer some options ? Now that Br*xit's been done, UK-based suppliers are suddenly last-choice for EU-based private (+trade??) buyers coz costs, especially for smaller orders, have skyrocketed. Shame really, but that's what people apparently wanted ...